the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

need relay with 130 ma or less


Post ReplyPost New Topic
< Prev Topic Next Topic >
ladybridgeport 
Member - Posts: 4
Member spacespace
Joined: May 20, 2006
Location: United States
Posted: November 19, 2011 at 12:08 PM / IP Logged  
I want to use my Audison Bit One processor, but for the remote turn on for my amps the manual says to use a relay that does not draw more than 130 mA. I keep finind 160 mA is the nominal. It's a SPDT 12DVC 30/40 amp relay. I will be only drawing an amp or two to turn on my amps, but want the standard size SPDT 5 prong relay, but has a acurrent draw of 130 mA max or less. Anyone know where to get one?
Ween 
Platinum - Posts: 1,366
Platinum spacespace
Joined: August 01, 2004
Location: Illinois, United States
Posted: November 19, 2011 at 1:48 PM / IP Logged  
Hi,
Did you measure the current required to turn on your amplifiers?
The amount needed may be well less than the amp or two you think, or even less than the 130mA output available on the Bit One. You might be able to find a solid-state (all electronic) equivalent of a bosch-type relay, but it will be pricey.
Mark
oldspark 
Gold - Posts: 4,913
Gold spacespace
Joined: November 03, 2008
Location: Australia
Posted: November 19, 2011 at 3:11 PM / IP Logged  
<130mA means a coil greater above 110 Ohm resistance (assuming 14.4V).
Many relays should meet that, though most automotive relays are 60-90 Ohms.
You could get a smaller relay to turn on whatever big relay you need for the amp.
Otherwise a transistor (or FET) could be used as a buffer. (Others have posted suitable tranny circuits previously.)
ladybridgeport 
Member - Posts: 4
Member spacespace
Joined: May 20, 2006
Location: United States
Posted: November 20, 2011 at 12:14 AM / IP Logged  
My one amp draw 100 ma and I'll have 3 amps and audio control matrix, whic hwill put it over 130 ma
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: November 20, 2011 at 2:19 AM / IP Logged  
Most of the PCB relays have higher coil impedencies and handle up to 10 amps. Excepting the size requirement (why that size? I always mix and match for different power requirements, considering it's about 1/4 the price) that's one answer.
i am an idiot 
Platinum - Posts: 13,668
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: November 21, 2011 at 9:48 AM / IP Logged  
100ma is EXTREMELY high for an amplifier remote wire. Did you actually test this, or is that what the manufacturer states?
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: November 21, 2011 at 10:06 AM / IP Logged  
I've just realised where this is going, in the mid 80s I had a (then) top end Nak cassette head unit, also an Alpine 12 disc autochanger, both feeding a Denon switching unit with three Soundstream amps, I never needed a relay.
ladybridgeport 
Member - Posts: 4
Member spacespace
Joined: May 20, 2006
Location: United States
Posted: November 22, 2011 at 11:28 AM / IP Logged  
I found a Panasonic relay that draws 117 Ma model: CB1AM12V it's a 12VDC relay 5 socket which should work. A guy I work with is powering 3 amps with his Bit One, but I'd rather be safe than sorry especially if I am gonna cruise Woodward cruise for 8 hours straight playing it.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Tuesday, April 30, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer