the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

python 323 lock fuse blows


Post ReplyPost New Topic
< Prev Topic Next Topic >
ephelan 
Member - Posts: 6
Member spacespace
Joined: December 13, 2011
Location: Nevada, United States
Posted: December 14, 2011 at 12:06 AM / IP Logged  
Components: Python 323, Hurricane Remote Start, 524k power door lock kit
Vehicle: 2011 Nissan Frontier Crew Cab
Knowledge: beginner
Everything works fine but the locks. The 15amp fuse on the violet wire keeps blowing(seemingly random). Below is what I have wired. Did I install incorrectly, or am I missing a ground/short somewhere?
python 323 lock fuse blows -- posted image.
offroadzj 
Gold - Posts: 2,041
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: June 03, 2005
Location: New York, United States
Posted: December 14, 2011 at 6:07 AM / IP Logged  
Do you have wiring information for the lock kit? MOST door lock modules require a - signal to activate the locks... so you would need to change your violet wire to ground instead of 12v (+). But I would check the wire diagram to verify it first. I can't seem to find anything on the 524k as far as wiring goes.
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: December 14, 2011 at 7:28 AM / IP Logged  
From the poster's colours I'm guessing it's either a Spal or MES kit with the blue timer relay.
Connect the violet/black and violet to ground, WHITE/ black and BROWN / black NOT connected, blue/black and GREEN/ black to violet and brown connect whichever way round locks on arming and unlocks on disarm. You can test this by grounding first the lock kit brown then violet, that should either lock then unlock or vice versa determining which one is the lock and which one the unlock trigger.
If that works the lock unlock correctly go on to join from the alarm as I said above.
ephelan 
Member - Posts: 6
Member spacespace
Joined: December 13, 2011
Location: Nevada, United States
Posted: December 14, 2011 at 10:27 PM / IP Logged  
The alarm and lock kit are products of Directed Electronics.
I'll try to scan the wiring tomorrow morning, though the legend provided shows the alarm's colors.
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: December 14, 2011 at 11:43 PM / IP Logged  

Based on what I see in the diagram.... why the relay kit?

The 323 has built in lock relays.... does it not?

ephelan 
Member - Posts: 6
Member spacespace
Joined: December 13, 2011
Location: Nevada, United States
Posted: December 15, 2011 at 1:43 AM / IP Logged  
Here is the wiring per manufacture:
Alarm Wiring
Lock Wiring
ephelan 
Member - Posts: 6
Member spacespace
Joined: December 13, 2011
Location: Nevada, United States
Posted: December 15, 2011 at 1:44 AM / IP Logged  
Yea I believe it does based on the wiring KarTuneMan. Does this mean I need to eliminate the kit relay?
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: December 15, 2011 at 2:14 AM / IP Logged  
Good catch Gary!
Wire the Python as I said above , eliminate the 524K relay and run the GREEN/ black to either the BCM at right of steering column* white, 15 pin plug to pin 5 purple.
Wire the blue/black to the same plug, pin 6 lt. green*
*Both are also located in the driver's kick panel.
ephelan 
Member - Posts: 6
Member spacespace
Joined: December 13, 2011
Location: Nevada, United States
Posted: December 18, 2011 at 5:24 PM / IP Logged  
As much as it pains me to type this, I don't understand what you're asking me to do. What do I need in the BCM for the door locks? I don't understand how I'm eliminating the lock kit relay when the only wires you mentioned belong to the alarm?
luig1094 
Member - Posts: 6
Member spacespace
Joined: December 28, 2011
Location: Massachusetts, United States
Posted: December 28, 2011 at 11:44 AM / IP Logged  
hey man could you PM me about how you got your starter working? I got the same set up but i can't get the starter to work connected through the alarm ...
ephelan wrote:
Components: Python 323, Hurricane Remote Start, 524k power door lock kit
Vehicle: 2011 Nissan Frontier Crew Cab
Knowledge: beginner
Everything works fine but the locks. The 15amp fuse on the violet wire keeps blowing(seemingly random). Below is what I have wired. Did I install incorrectly, or am I missing a ground/short somewhere?
python 323 lock fuse blows -- posted image.
You can do anything !
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Wednesday, April 14, 2021 • Copyright © 1999-2021 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer