the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

remote start, 2007 nissan armada


Post ReplyPost New Topic
< Prev Topic Next Topic >
jiriki 
Member - Posts: 16
Member spacespace
Joined: January 08, 2012
Location: Ohio, United States
Posted: February 13, 2012 at 4:59 PM / IP Logged  
Yep. I got the neutral safety switch installed and in the "on" position.
Going to hook up the brake wire now...
jiriki 
Member - Posts: 16
Member spacespace
Joined: January 08, 2012
Location: Ohio, United States
Posted: February 13, 2012 at 6:56 PM / IP Logged  
Still flashes 7 times and I cannot get into the "menu" system. Clicking the valet button doesn't do anything following your procedure or the ones in the manual. It seems like it's locked but my suspicion is that pink heavy gauge wire.
Primary Harness
H1/2 Red - 12v constant -> Vehicle Battery Positive Wire (+): Green
H1/5 Black - ground -> Common ground bolt on frame
H1/11 White - Parking lights -> Connected to parking light wire at dimmer switch
Heavy Gauge
H3/1 Pink - Ignition 1 input/ouput -> FLCAN Pink Ignition input
H3/2 RED / White - (+) FUSED (30A) IGNITION 2 / FLEX RELAY INPUT 86a -> Vehicle Battery Positive Wire (+): Green
H3/3 Orange - Accessory Output - > Vehicle Accessory 1
H3/4 Violet - Starter Output -> Starter 1 and 2 (I have the relay but misplaced it so I need to either find it again or go buy another one)
H3/5 Red - (+) FUSED (30A) IGNITION 1 INPUT -> Vehicle Battery Positive Wire (+): Green
H3/6 Pink/White - (+) IGNITION 2 / FLEX RELAY OUTPUT 3 -> Vehicle Ignition Wire (+): BLACK/ Red
H3/7 Pink/Black - FLEX RELAY INPUT 87A key side (if required) -> NOT CONNECTED
H3/8 RED / Black - (+) FUSED (30A) ACCESSORY/STARTER INPUT -> Vehicle Battery Positive Wire (+): Green
Remote Start input, 5 pin
H3 Brown - (+) BRAKE SHUTDOWN INPUT -> Brake switch at the pedal
Other
12. Neutral saftey switch toggle set to "on"
http://www.acsdistributors.com/uploads/techinfo/viper/manuals/5301v%20Install.pdf
The manual states that in order to program it out of MTM mode, the heavy gauge pink wire needs to be installed. However, it is not connected to the vehicle but connected to the FLCAN. Could that be my problem?
offroadzj 
Gold - Posts: 2,043
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: June 03, 2005
Location: New York, United States
Posted: February 13, 2012 at 7:05 PM / IP Logged  
Yes, that is your issue; the Pink ignition wire off the Viper needs to go to your vehicle ignition wire. Then the pink ignition wire on the FLCAN will tie into that wire. It is not a direct connection just between the 2. Then connect the pink/white to your accessory 2 wire in the vehicle and set the programming option to 2nd accessory.
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205
jiriki 
Member - Posts: 16
Member spacespace
Joined: January 08, 2012
Location: Ohio, United States
Posted: February 13, 2012 at 9:13 PM / IP Logged  
That worked. I was able to get into the menus.
I must have tried it several dozen times but I was not able to get the program out of MTM mode.
Is it possible it's locked?
offroadzj 
Gold - Posts: 2,043
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: June 03, 2005
Location: New York, United States
Posted: February 13, 2012 at 9:27 PM / IP Logged  
Did you confirm the menu and level selection by the LED? Did the LED flash the correct number of times for the AT option after pressing the remote?
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205
jiriki 
Member - Posts: 16
Member spacespace
Joined: January 08, 2012
Location: Ohio, United States
Posted: February 13, 2012 at 10:08 PM / IP Logged  
Yes... at least that's what the manual says is the menu for AT.
I would hold the button down, it would flash once, pause, flash twice, pause, flash tree times... let go. Hit the button once and release. Hit the button and hold, flash once. Click unlock and get two flashes. Let go of valet button. Cycle "on/off" ignition.
offroadzj 
Gold - Posts: 2,043
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: June 03, 2005
Location: New York, United States
Posted: February 13, 2012 at 10:10 PM / IP Logged  
It sounds like you are programmed correctly. What exactly is happening when you try to remote start it? Are the other functions working properly (locks, parking lights, etc)
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205
jiriki 
Member - Posts: 16
Member spacespace
Joined: January 08, 2012
Location: Ohio, United States
Posted: February 13, 2012 at 10:43 PM / IP Logged  
The door locks and unlocks properly.
Parking lights flash with the lock and unlock function.
The parking lights also flash when it flashes 7 times when I attempt to remote start.
The trunk release does not work however. The Nissan armada has an automatic lift gate so I don't know if it is compatible with that or not.
When I unlock the doors, the valet LED flashes. When I open the door, the valet LED stops flashing.. so it seems to know the door pins.
Is there a factory reset on the unit that I can do without a bitwriter?
offroadzj 
Gold - Posts: 2,043
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: June 03, 2005
Location: New York, United States
Posted: February 14, 2012 at 5:53 AM / IP Logged  
What do you have the BLACK/ white neutral safety switch wire connected to? Did you successfully learn the tach signal?
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205
jiriki 
Member - Posts: 16
Member spacespace
Joined: January 08, 2012
Location: Ohio, United States
Posted: February 14, 2012 at 10:34 AM / IP Logged  
The neutral safety switch is connected to a real toggle switch. (maybe i'm confusing that with something else...)
I started the car with the key.. it did not learn the tach signal. I believe it's supposed to light up a solid red LED when it's learned the signal but it never happened.
Page of 3

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Saturday, May 3, 2025 • Copyright © 1999-2025 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer