the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2007-2012 Jeep Patriot Remote Start Pictorial


Post ReplyPost New Topic
< Prev Topic Next Topic >
kreg357 
Platinum - Posts: 7,465
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: New York, United States
Posted: December 29, 2013 at 4:20 PM / IP Logged  

The White sticker with the install guide number might be on the ADS ALSL CH package ( the box it came in with the Flash access hole in the bottom and plastic bag of harnesses ).

Worst case scenario, dump the CH5 harness and go W2W...

Soldering is fun!
Talent421 
Member - Posts: 10
Member spacespace
Joined: December 02, 2004
Location: United States
Posted: December 30, 2013 at 4:12 PM / IP Logged  
I plan on trying 2 more things before I trash the harness and go w2w. Am I going to need relays and resistors to pull that off or will the bypass module handle all that?
Talent421
kreg357 
Platinum - Posts: 7,465
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: New York, United States
Posted: December 30, 2013 at 7:42 PM / IP Logged  
If you dump the CH5 harness and go W2W, the only thing extra you will need is a 1N4001 diode.  The Type 3 install looks
complicated but the bypass module only has 5 connections to the Jeep.  The U1280 remote starter only has 4 wire
connections to the Jeep ( +12V constant power, chassis ground, Parking Lights and the Hood Pin ).  Then there are
the wire connections between the U1280 and the bypass module.  That's it.  You could even go D2D between the modules
and then make the wire connections shown with solid Black and the necessary Red lines.
Soldering is fun!
Talent421 
Member - Posts: 10
Member spacespace
Joined: December 02, 2004
Location: United States
Posted: January 01, 2014 at 2:45 PM / IP Logged  
Kreg357,
I just wanted to post a follow up to this remote start install.
Finally got it figured out!!!
I really want to thank you for all your help. You made the difference between success and failure and you saved me about $200 in installation charges that Best buy wanted to do this car.
Thanks again.
Scott
Talent421
Page of 3

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, September 16, 2021 • Copyright © 1999-2021 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer