the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

adding power windows and locks


Post ReplyPost New Topic
< Prev Topic Next Topic >
xchrisx 
Copper - Posts: 197
Copper spacespace
Joined: August 19, 2008
Location: Pennsylvania, United States
Posted: February 18, 2012 at 6:36 PM / IP Logged  
Ok, so I just picked up a 2000 Plymouth Neon 5spd, BUT it has been swapped to an 05 Dodge Neon SRT-4, including the wiring harness on the inside of the car.
I want to add power door locks and power windows...I was thinking of just going to the local scrap yard and yanking out the wiring and motors for both the door locks and power windows from a neon with all power options, however I am not sure if they will just plug an play or if the wiring will be different.
If anyone knows if they're the same harnesses or different and if different what is what, it'd be greatly appreciated.
Thanks.
bp
racerjames76 
Silver - Posts: 581
Silver spacespace
Joined: November 22, 2008
Location: Ohio, United States
Posted: February 22, 2012 at 10:00 AM / IP Logged  

Highly reccomend getting the OEM window motors, and switches too if you like. Some research into what is there in the car will help with your other question, or you can get a universal power window switch kit and run the OEM motors off that. I have had 0 luck with the SPAL window motors so stay away from those.

The door locks really dont matter. All aftermarket lock motors are pretty much created equal, and really arent any better or worse than OEM. Just takes a little engineering to physically move the locks.

To master and control electricity is perfection. *evil laugh*
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: February 23, 2012 at 10:39 AM / IP Logged  
OK in essence RJ you are absolutely correct and I do believe that Neon follows Spal lo0ck and windows.
xchrisx 
Copper - Posts: 197
Copper spacespace
Joined: August 19, 2008
Location: Pennsylvania, United States
Posted: February 24, 2012 at 3:12 PM / IP Logged  
Well, I was thinking more along the lines of factory stuff from a neon. Would I be able to just add the power door lock switch, metal arms that attach to the little...flipper i guess on the door lock on the door, and plug the wire in? Or do I need the actual latch to be power also? Sorry if it doesn't make sense.
bp
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: February 24, 2012 at 3:19 PM / IP Logged  
You have to see if all the looms are in place in the doors, very much doubt it but they are you probably only have to add fuses and switches and relay and motors and actuators to make it go

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, December 1, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer