2003 chrysler town country parking lights

Home / the12volt's Install Bay / Car Security and Convenience / 2003 chrysler town country parking lights (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

usmcvet

Member - Posts: 10

Joined: January 18, 2011

Location: Illinois, United States

Posted: August 05, 2012 at 1:37 PM / IP Logged

Installing a R/S on a 2003 Chrysler T & C and it says the parking light wire is a NEGATIVE BROWN / white at the switch,but there is no WHITE/ brown or BROWN / white at the back of the parking light switch. R/S works fine but having problems finding the parking light wire. Thanks !

Back to Top

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: August 05, 2012 at 3:15 PM / IP Logged

Go to the Downloads/Manuals section above, in the right hand search bar, enter DEI 1082.

It's more complicated than you think, requires a relay and a resistor.

Back to Top

usmcvet

Member - Posts: 10

Joined: January 18, 2011

Location: Illinois, United States

Posted: August 05, 2012 at 3:30 PM / IP Logged

Ok,Thanks ! On the relay # 87 is to the resistor,just wire both ends of the resistor together and wire to # 87 on the relay ? Thanks !

Back to Top

usmcvet

Member - Posts: 10

Joined: January 18, 2011

Location: Illinois, United States

Posted: August 05, 2012 at 3:39 PM / IP Logged

I see now about the resistor,one ends goes to ground. On the # 30 on the relay it says it goes to lights. What lights ?

Back to Top

kreg357

Platinum - Posts: 7,783

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: August 05, 2012 at 4:07 PM / IP Logged

At the light switch connector there is a WHITE/ Brown wire ( MUX wire ). You cut that wire and connect the correct ends to the relay pins shown. You are isolating the switch when the R/S outputs its' Parking Light signal and applying the 2.1 k ohm resistor to the vehicles MUX circuit to turn on the Parking Lights.

Soldering is fun!

Back to Top

enice

Silver - Posts: 857

Joined: March 05, 2006

Location: New York, United States

Posted: August 06, 2012 at 10:41 AM / IP Logged

Just get a WHITE/ orange(+) wire at the driver's kick panel. No need for a relay or resistor.

Back to Top

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: August 06, 2012 at 10:46 AM / IP Logged

Ta Eric, I've only ever done Audio, Bluetooth and tracking, heck it's called a Chrysler Voyager here and built in Austria!

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

2003 chrysler town country parking lights

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.