05 chevy equinox will not crank

i dont see it on the diagram for the bypass but it has it on the vehicle wiring info and says it is required. Keysense lt. green (required)   -   BCM, 24 pin gray plug, pin A8 just wondering if there is a connection off the remote start module to hook this up to?

Found the following on a different site:  Could use the Ground When Running with diodes. (-) GWR from the Viper

The GREEN Key Sense Wire Must See A Ground When Running. If Not The Service Required Light Will Come On. Its The Light With The Car And Wrench On It.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

ok what do i hook it up to so it sees ground when remote start is activated?

H2/3 Blue/White as second status. or H2 Dark Blue status output.When all else fails, Read the Instructions

Support the12volt.com Make a Donation

do i still need to use a diode for either of those?

ok so it still wont start..i even tried just grounding that wire myself when remote start is activating..im am getting really confused. the remote start activates and then it loses power on the accessory wires, and then is supposed to crank the starter, you can tell when it wants to crank but doesnt. then if i put the key in the ignition and turn to the ON position it starts right up and i can then take the key out of the ignition and it keeps running and i can disable it with the remote start key fob. any ideas on what i could be missing?

should the starter still crank if i take the bypass module completely out of the loop? like crank and not start or start but die right away?

Link to another equinox with info on keysense and diode: https://www.the12volt.com/installbay/forum_posts.asp?tid=125491&tpn=1&PN=1

Can you list all of your wire connections from the viper to the car and from the XK09 to ???

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

vehicle        remote starter constant 12 volts - RED / white (x2) /// 4 wires > small red, heavy red     RED / black, RED / white ignition pink      ///     pink accessory 1 orange ///     orange accessory 2 brown ///     pink white keysense lt. green ///     not sure ??? power lock lt. blue///     green (with relay) power unlock dk blue  ///     blue (with relay) park lights brown +///     white tach purple       ///      violet/white brake lt. blue    ///      brown bypass ignition pink    ///        pink ign to bcm orange black        ///        black ign to bcm yellow///    yellow/black & yellow (spliced) 12v red ///        red starter output from RS violet   ///        violet status output from RS blue      ///        blue/white these are the wire i have .... i have taken the bypass out of the loop tho. please any help would be appreciated

Lets make sure we are on the same install diagram.  Type 6 XK09?  Right??

Viper H3 harness.. H3/1 pink is connected to pink on ignition harness and to pin 8 pink of 20 pin connector

H3/4 violet to pin 7 violet of 20 pin connector

H3/6 Pink/White is default to Ignition 2, change it to ACC 2 in the Viper Brain.

Viper H2/9 Dark Blue to Pin 1 Blue/White of XK09, 20 pin conn

Pin 9 Red of 20 Pin conn to 12 volts constant...Pin 10 Black of 20 Pin to Black OR ORANGE / Black at ignition switch

Pin 12 yellow/black to pin 15 yellow, 20 pin conn, then to yellow at ignition switch

Pin 13 violet/brown to pin 16 brown, 20 pin conn

Viper H2/3 Blue/white to keysense or car...Set to 2nd status in Viper Brain.

Then program the XK09 to the car per the programing instructions.

What have you got the Vipers Tach wire connected to???    Are all your connections soldered??  Make sure you test the wires you are connecting to with a DMM.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation