avital 5303 in a 07 suzuki forenza

So ALL the doors lock and unlock using the interior switch ? Including the drivers door ? If so then there is a light GREEN / WHITE for lock and a yellow unlock in the dkp.   Both negative triggerIf i Can't Install it    I Don't need it   Joe

Yes all doors lck and unlck with driver door switch. When do I use relays

No relays should be needed for the locks. The 5303 has negative lock outputs that are used to control the cars factory relays. In your case the wire colors I listed above should work directly connected. Test everything using a meter before connecting into any wiringIf i Can't Install it    I Don't need it   Joe

When do I use relays tho I'm having trble understanding relays. Will I need relays at all for the avital 5303

H1/1 (need relay?) RED / WHITE (-) 200mA TRUNK RELEASE OUTPUT brown (driver kick pannel) H1/2 RED (+)12v CONSTANT POWER INPUT red (igition switch) H1/3 BROWN (+) SIREN OUTPUT red of siren and black wire of siren ground to chassis H1/5 BLACK (-) CHASSIS GROUND ground to chassis H1/6 VIOLET (+) DOOR TRIGGER INPUT, ZONE 3 dnt use H1/7 BLUE (-) MULTIPLEX INPUT, ZONE 4 blue and green wire of dual shock sensor H1/8 GREEN (-) DOOR TRIGGER INPUT, ZONE 3 purple (driver kick, harness to rear) H1/9 BLACK/ WHITE   (need relay?) (-) 200mA DOME LIGHT OUTPUT SUPERVISION OUTPUT not sure H1/10 WHITE/ BLUE REMOTE START (-) ACTIVATION INPUT not sure H1/11    (need relay?) WHITE (+/-) SELECTABLE LIGHT FLASH OUTPUT PURPLE / white (L), BROWN / white (R)   (driver kick,harness to rear) H1/12 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT not sure H2/1 LIGHT BLUE 200mA (-) 2nd UNLOCK OUTPUT not sure H2/2 WHITE/ BLACK 200mA PROGRAMMABLE (-) AUX 2 OUTPUT not sure H2/3 VIOLET/BLACK (-) 200mA PROGRAMMABLE (-) AUX 1 OUTPUT not sure H2/4 GREEN / WHITE FACTORY ALARM REARM OUTPUT lt. blue (driver door key cylinder)driver kick, door harness      H2/5 GRAY/BLACK (-) DIESEL WAIT TO START BULB INPUT dont need H2/6 LIGHT GREEN/ BLACK   (need relay) FACTORY DISARM OUTPUT lt. green (driver door key cylinder)driver kick, door harness H/1 PURPLE (+) STARTER OUTPUT blue(starter motor) H/2 GREEN STARTER INPUT blue(key igition) H/3 RED (2) (+) 12V INPUT FOR HIGH CURRENT OUTPUTS not sure H/4 ORANGE (+) ACCESSORY OUTPUT not sure H/5 PINK (+) IGNITION OUTPUT pink(ignition harness) H/6 PINK/WHITE (+) SECOND IGNITION ACCESSORY OUTPUT brown(ignition switch) H/7 RED / WHITE (+) 12V INPUT H/2 H3/1 BLACK/ WHITE NEUTRAL SAFETY SWITCH INPUT not sure H3/2 VIOLET/WHITE

H3/2 VIOLET/WHITETACHOMETER INPUT gray(instrument cluster) H3/3 BROWN (+) BRAKE SWITCH INPUT, ZONE 1 lt. blue (brake switch or driver kick) H3/4 GRAY (-) HOOD PIN SWITCH INPUT, ZONE 1 hood pin H3/5 BLUE/WHITE (-) STATUS OUTPUT not sure H4/1 ORANGE / BLACK 200 mA PROGRAMMABLE (-) AUX 3 OUTPUT not sure H4/2 BROWN 200mA (-) HORN OUTPUT not sure LIGHT BLUE (-) UNLOCK OUTPUT lt green(driver kick) LIGHT BLUE (-) UNLOCK OUTPUT yellow(driver kick)

Why not set the Avital 5303 H1/11 White Parking Light output to (-) and connect it to Parking Lights     White (-)     @ headlight switch, 6 pin plug, pin 6 ? If you wish to use the Forenza's (+) Parking Light Rt & Lt wires you must use a relay or two 8 Amp diodes to isolate the two wires. H/1 PURPLE (+) STARTER OUTPUT Blue cut wire (starter motor side) H/2 GREEN STARTER INPUT Blue cut wire (key igition side) H/3 RED (2)(+) 12V INPUT Red @ Ignition switch harness H/4 ORANGE (+) ACCESSORY OUTPUT        Orange @ Ignition switch harness H/5 PINK (+) IGNITION OUTPUT        Pink(ignition harness) H/6 PINK/WHITE (+) 2nd IGNITION / ACC OUTPUT      Brown(ignition switch)   ******Set to ACC2 H/7 RED / WHITE (+) 12V INPUT  Red @ Ignition switch harness H3/1 BLACK/ WHITE NEUTRAL SAFETY SWITCH INPUT     To chassis ground or Parking Brake H3/5 BLUE/WHITE (-) STATUS OUTPUT not usedSoldering is fun!

on H/6 PINK/WHITE (+) 2nd IGNITION / ACC OUTPUT      Brown(ignition switch)   ******Set to ACC2 what do you mean set to acc2? H1/1 RED / WHITE (-) 200mA TRUNK RELEASE OUTPUT brown (driver kick pannel) do i need A relay?

H1/9 BLACK/ WHITE   (need relay?) (-) 200mA DOME LIGHT OUTPUT SUPERVISION OUTPUT not sure H2/6 LIGHT GREEN/ BLACK   (need relay) FACTORY DISARM OUTPUT lt. green (driver door key cylinder)driver kick, door harness i need a relay for this one correct?

And will the driver door set off all door triggers?