2011 camry and viper 5706v

Home / the12volt's Install Bay / Car Security and Convenience / 2011 camry and viper 5706v (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

howie (aka: harryharris)

Silver - Posts: 355

Joined: February 17, 2014

Location: Florida, United States

Posted: March 19, 2014 at 1:02 PM / IP Logged

True1, your last question ref. relay and diode is correct, did you mention analog meter at one point?

Don't unless like me you know what you're doing an analog meter will fry any chip driven components.

Test before boxing up.

thrue1

Copper - Posts: 77

Joined: December 09, 2008

Location: Illinois, United States

Posted: March 19, 2014 at 1:16 PM / IP Logged

Yes: it's not hooks up yet ; just testing and getting relay ready

howie (aka: harryharris)

Silver - Posts: 355

Joined: February 17, 2014

Location: Florida, United States

Posted: March 19, 2014 at 1:23 PM / IP Logged

Test before boxing up.

vin123

Member - Posts: 28

Joined: February 22, 2014

Location: Minnesota, United States

Posted: March 21, 2014 at 8:54 PM / IP Logged

thrue1, can you let me know how it goes with your installation?

I'm still waiting for my orders and weather to warm here..

vin123

thrue1

Copper - Posts: 77

Joined: December 09, 2008

Location: Illinois, United States

Posted: March 22, 2014 at 4:57 AM / IP Logged

I got prep work done with the relay, and used plastic ties on unused wires. I don't want to cut them, maybe for the future

thrue1

Copper - Posts: 77

Joined: December 09, 2008

Location: Illinois, United States

Posted: March 23, 2014 at 2:03 PM / IP Logged

Question,

The viper 5706v did not come with an led light? Is that correct?

thrue1

Copper - Posts: 77

Joined: December 09, 2008

Location: Illinois, United States

Posted: March 23, 2014 at 2:17 PM / IP Logged

The control button and led are both on the antenna? Correct?

thrue1

Copper - Posts: 77

Joined: December 09, 2008

Location: Illinois, United States

Posted: March 23, 2014 at 2:50 PM / IP Logged

Question,

When I connect hood pin switch in the engine bay and run the wire back into 24 pin, gray wire (9), do I need to put any diodes in between?

howie (aka: harryharris)

Silver - Posts: 355

Joined: February 17, 2014

Location: Florida, United States

Posted: March 23, 2014 at 2:53 PM / IP Logged

No, why would you need to?

Especially when it's here, not in the engine bay:-

Left of steering column, gray 25 pin plug, pin 2

Test before boxing up.

thrue1

Copper - Posts: 77

Joined: December 09, 2008

Location: Illinois, United States

Posted: March 23, 2014 at 3:00 PM / IP Logged

I heard in some online video, ok thank u

In most cases hood pin should be as NO, Meaning when hood is closes it should see ground

Pin 9,gray is as (-) hood pin input (NC or NO)

I need to set to NO , because of hood is open it is not depressed, but when closed ground is seen by pin 9.

Explain if wrong

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.