the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

remote start catx630


Post ReplyPost New Topic
< Prev Topic Next Topic >
judsonlis 
Member - Posts: 3
Member spacespace
Joined: October 03, 2014
Posted: October 03, 2014 at 11:57 AM / IP Logged  

I recently purchased a replacement Code Alarm Remote CA-TX630. I followed the directions and the alarm programmed fine, but the remote start feature no longer works. It is not in Valet mode. When I hold down the bottom right blue button my car beeps and lights flash 4 times??? please help. thanks

catback 
Silver - Posts: 697
Silver spacespace
Joined: August 13, 2002
Location: Canada
Posted: October 04, 2014 at 10:36 AM / IP Logged  
4 flashes indicates remote start valet mode is on. Take the unit out of valet mode.
judsonlis 
Member - Posts: 3
Member spacespace
Joined: October 03, 2014
Posted: October 06, 2014 at 7:27 AM / IP Logged  
Unfortunately, I have put it on and off Valet mode several times.  I know it is on or off because when it's on, the Blue LED is flashing on my dash.  The hood and truck are closed.  Any other ideas why remote start would not work?????   
catback 
Silver - Posts: 697
Silver spacespace
Joined: August 13, 2002
Location: Canada
Posted: October 06, 2014 at 9:24 AM / IP Logged  
Ok that was worth a blind shot.
I'm guessing you have either a Code Alarm CA530 or CA630, and info from the CA530 manual says
"Unit will chirp 4 times if tach is not yet learned or vehicle has not been
manually started if in Blind Crank Timing Mode."
judsonlis 
Member - Posts: 3
Member spacespace
Joined: October 03, 2014
Posted: October 06, 2014 at 9:39 AM / IP Logged  
Yes, it is a CA630.  Not exactly sure what "tach is not yet learned or vehicle has not been
manually started if in Blind Crank Timing Mode"  is?    Is this something I can do myself??  Thanks.
catback 
Silver - Posts: 697
Silver spacespace
Joined: August 13, 2002
Location: Canada
Posted: October 06, 2014 at 10:38 AM / IP Logged  
I suggest taking a look at the installation manual for your system.
The manual for the 530 is on this site here
Browse the programming section for the relevant info.
As to what tach and blind crank is, it's how the remote start determines when to stop cranking when starting the car. Tach is monitoring the rpm of the engine to determine when it's running. Blind crank is cranking the starter for a pre-determined amount of time and expecting that the car has started by the end of it.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, September 29, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer