2010 accord crosstour

Home / the12volt's Install Bay / Car Security and Convenience / 2010 accord crosstour (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

ziggyb222

Silver - Posts: 593

This member has made a donation to the12volt.com. Click here for more info.

Joined: January 04, 2004

Location: Maine, United States

Posted: January 10, 2015 at 4:19 PM / IP Logged

Installing a Clifford 4105 in a Honda Crosstour. Using a ADS-ALCA flashed with the DL-HA3 firmare. It programmed correctly but all I get is light flashes and the locks work..but no crank. Everything is soldered and the connection type is hardwired..no data,,,,HELP!!!!!lol

chev104275

Gold - Posts: 1,427

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: November 26, 2007

Location: Massachusetts, United States

Posted: January 10, 2015 at 5:36 PM / IP Logged

Does the car crank at all ? I haven't done a crosstour nor do I do a lot of code alarm but reading the ads ca install guide there's a warning about the gwr coming on before ignition or it will cause immobilizer issues have you tested the gwr ?

If i Can't Install it I Don't need it Joe

Chris Luongo

Platinum - Posts: 3,746

This member consistently provides reliable information

Joined: May 21, 2002

Location: Massachusetts, United States

Posted: January 10, 2015 at 7:44 PM / IP Logged

Did you program tach?

Where is the BLACK/ white wire on the Clifford connected?

ziggyb222

Silver - Posts: 593

Joined: January 04, 2004

Location: Maine, United States

Posted: January 10, 2015 at 7:47 PM / IP Logged

I tried everything..grounded the module before ignition..same thing.. tried leaving the key in the ignition.. I will probably use the firmware just for imobilizer and hard wire the locks and acc ign and starter to the car.. Not in less anyone else has some options????

ziggyb222

Silver - Posts: 593

Joined: January 04, 2004

Location: Maine, United States

Posted: January 10, 2015 at 8:22 PM / IP Logged

BLACK/ wht is to ground...tach for the clifford to the purle/wht on the ALCA!! Remote start clicks and tries three time...the dash lights never fire up and does not even try to crank

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: January 10, 2015 at 8:43 PM / IP Logged

Must have a bad brain. I have done it gen accords without a problem. Meter all rs outputs ?

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

ziggyb222

Silver - Posts: 593

Joined: January 04, 2004

Location: Maine, United States

Posted: January 10, 2015 at 8:53 PM / IP Logged

I had originally tried data...did the same thing...Metered the ignition at the switch...after I hardwired it it was the same...I did not check the output on the start wire connected to the BLACK/ wh on the alca!!!!

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: January 10, 2015 at 9:19 PM / IP Logged

Any diagnostics ?

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

ziggyb222

Silver - Posts: 593

Joined: January 04, 2004

Location: Maine, United States

Posted: January 10, 2015 at 9:23 PM / IP Logged

I noticed when attempting to remote start...I get five green light flashes...the as the start continues to try two more time there is not activity on the green light...

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: January 10, 2015 at 10:50 PM / IP Logged

i would reprogram the alca. can you do pit stop mode?

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.