Viper 5305V Remote Start, 2008 Toyota Corolla

Ok I'll check the wires with a dmm correct? That won't cause a problem with that correct? I know for a fact I had no power at the cut wire starter side connected to the violet wire off 10 pin harness H7. What am I looking for at the ignition wires main BLACK/ white and 2nd ignition BLACK / YELLOW for power? The toggle switch is on for sure one end going to ground and the other going to H13 BLACK/ white on 24 pin harness. When its off nothing happens seams correct. Got you on the WHITE/ blue won't make it permanent. Yes the car does start with the key when I had it hooked up. I'm going to solder in the power this time into the white wire making a tee harness so I don't have a big goob on one connection split it up neatness. I also had to program the module per the flashligic guide for wire diagram #2 that went ok followed the instructions.

Ign wires will have +12v when key is in on/run position. Starter wire will only show +12 in the crank position.

Ok I'll be sure to check that thanks. Also I called the place I got the module from they are going recheck how they flashed it might be a problem I will call them when I have it all hooked up again in the car to confirm program the light didn't flash correct when I did it two times have up check every possible issue.

Ok I'm back in the saddle under the dash with the key on I have 12 volts on ignition 1 and same on ignition 2 also I have power at accessory with key on. I'm going to hook up all wires now as manual states. Starter wire has power when all the turned.

Hello, well I soldered all the connections this time and made sure to check all wiring connections twice before making them permanent. I checked all fuses and they are good. I called the vendor to make sure I set up programming for flashlogic module correct they walked me thru it and confirmed it's correct. I'm using DTD mode and wiring confirmed correct. I can't think of what I missed on this install the ground is good the car dash lights up as if I have key in ignition cycles on and off 3 times and that's it no start still. They did have me try and remote start the car with key in ignition and they said it should remote start but it didn't they told me it has to be incorrect wiring or problem with the viper 5305v unit on the remote start. The alarm works perfect locks doors parking lights good, chirps every command. I'm thinking it's a bad remote on the unit itself I'm ready to throw in the towel I appreciate all the great advise you gave me but not sure what else to do might be time to get help from a viper dealer. Thanks again.

Are you sure you have the two sides of the start kill relay connected correctly? PIn 6 and 7 on the heavy gauge harness. Put your dmm on pin 7 (starter side) and attempt to remote start. See if it shows +12v at any point.

I will check in the morning but I'm pretty sure I did that the manual said to do it in troubleshooting and I had nothing Violet wire to red cut starter wire, starter side Im getting no power transfer wherever that happens. I pulled all the fuses out checked with meter and they were good. It's nuts.

Do you think I'm missing any wires on 24 pin harness there was not many to this car was just going for the basics. H17 is not hooked up to anything, H2 I didn't hook up . If you have any suggestions I'm all ears.

You'll have to type out every wire and what you connected them to. Preferably colours and location of what you connected to as well.

Sorry,that was my next step to give you a recap of what I did so far.. Main Harness 5-pin Connector as follows I'll call this H1. H1=Black to good ground = yes H2=Brown to Siren = yes works H3=red to 12 volt source white wire ignition switch white plug pin 1 H4=Orange not connected H5=white to parking lights to green driver's kick panel works.. Auxiliary/shutdown/trigger Harness H2 as follows. . H13=BLACK/ white* to one side to toggle switch or side to ground and on. H20=brown to the brake pedal switch GREEN / WHITE above pedal H9=Gray Hood pin switch not hooked up yet H12=Violet/White tachometer not hooked up. Remote Start, 10 pin harness H3 ... H1= no connection N/C H2=RED / Black to 12 volts white wire at ignition white plug pin 1. H3=Pink/Black not connected N/C H4=Pink/white to 2nd ignition wire BLACK / YELLOW white plug pin 2. H5=Red to 12 volt source white wire ignition switch white plug pin 1. H6=Green to starter input key side of cut wire to red wire white plug pin 4. H7=Violet to starter output car side of cut wire to red wire. H8=Orange to accessory to Blue/Red wire white plug pin 3. H9=RED / White to 1q volt source white wire white plug pin 1. H10-Pink ignition one input/output to BLACK/ white White plug pin 6. Now for the flashlogic module connections. .. Using the D2D cable and programed correct to the car 2008 toyota corolla. Automatic Pink wire to ignition input with main harness Pink wire. WHITE/ black wire key sense to blue/black on car key switch black plug pin 2. White wire to ground. GREEN/ Red = code on the car Blue wire at transponder. Gray/Red = TXCT to car wire green wire at transponder. And that's pretty much it for what I hooked up other than the door harness wires that work the lock fine.     Thankyou for taking the time for looking at this for me you must have put a few of these in.