Viper 5706v, DBALL2, 2011 Chevy Cruze

Home / the12volt's Install Bay / Car Security and Convenience / Viper 5706v, DBALL2, 2011 Chevy Cruze

Welcome Guest :)

Members

Search

Register

Login

< Prev Page < Prev Topic Next Topic >

cruze625

Member - Posts: 13

Joined: February 23, 2016

Location: Illinois, United States

Posted: April 11, 2016 at 10:10 AM / IP Logged

SUCCESS! I wanted to post the solution in case others have a similar problem. Below are the differences that are not documented that led to success.

KEY DIFFERENCES NOT DOCUMENTED:

Starter wire Violet from Viper to DBALL2 MUST to be hooked up W2W. D2D not reliable.

Ignition 1 Input Red on Viper 10pin must be hooked up to 12V constant.

Re-flashed with 3.18+ and reprogrammed with spare GM OEM key. Apparently it was common for one GM key to be bad. DO NOT hard reset after it is flashed. This caused issues and some of the feature programming is lost.

VIPER WIRING - 6pin

+12V - Red ---> OBDII Pin 12 (+12V)

-Ground - Black ---> Chassis Ground

VIPER WIRING - 10pin

+Ignition - Pink ---> Ignition Switch Pin 1 - Violet/Black

+Starter Output - Violet ---> DBALL2 +Starter Input - Violet

+Fused 12V Ignition 1 Input - Red ---> OBDII Pin 12 (+12V)

DBALL2 WIRING - 14pin

SW CAN - Light Green ---> OBDII Pin 1 - Green

CAN High - Tan/Blank ---> OBDII Pin 6 - Blue

CAN Low - Tan ---> OBDII Pin 14 - White

Immo. Data (Module side) - ORANGE / Red ---> Immo. Module Pin 2 - Violet/Green

Immo. Data (Car side) - Yellow/Red ---> Immo. Module - Violet/Green

Immo. Data - BROWN / Red ---> DBALL2 12pin Immo. Data - Yellow/Black

DBALL2 WIRING - 12pin

+Accessory Output - Gray/Black ---> Ignition Switch Pin 3 - Violet / YELLOW

Immo. Data - Yellow/Black ---> DBALL2 14pin Immo. Data - BROWN / Red

DBALL2 WIRING - 10pin

+Starter Input - Violet ---> VIPER +Starter Output - Violet

General Notes

Neutral Safety/Parking Brake Input - BLACK/ White ---> Chassis Ground

Clutch Switch not needed (automatic) and parking lights from Viper not hooked up.

XpressKit wiring type 1a (without T-Harness) for GM10 v. 3.18+.

OBDTHDGM2 T-harness so don't have to tap into the OBDII wires.

VIPER Parking Lights wire not hooked up (not required but definitely a nice feature, helps to see error codes and running).

DBALL2 Driver Door Sense Trigger (not required but some console lights stay on for ten minutes otherwise.)

Back to Top

< Prev Page

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.