the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Honda Ridgeline problem with DBALL 2


Post ReplyPost New Topic
< Prev Topic Next Topic >
jvaguiar 
Member - Posts: 4
Member spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: February 07, 2016
Location: Texas, United States
Posted: March 17, 2016 at 1:44 PM / IP Logged Link to Post Post Reply Quote jvaguiar
I need you guy expertise
I have a Honda Ridgeline 2008. I installed an Avital 4103 remote starter with DBALL 2. I am using D2D installation. Everything is working fine, except:
After a remote start, even with the original key inserted, the car is still asking for the key. The car rum normally, but it is bothering me.
When I do a normal start, it does not happen.
Any idea?
smokeman1 
Platinum - Posts: 1,588
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: September 14, 2009
Location: Wisconsin, United States
Posted: March 17, 2016 at 8:57 PM / IP Logged Link to Post Post Reply Quote smokeman1
Are you talking about the security light?
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
jvaguiar 
Member - Posts: 4
Member spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: February 07, 2016
Location: Texas, United States
Posted: March 17, 2016 at 9:10 PM / IP Logged Link to Post Post Reply Quote jvaguiar
I Thanks.
No i am talking about the green light symbol located on instrument.
It is a green light key symbol that blink when the key is not inserted
Regards
Jose Aguiar
beegbie 
Copper - Posts: 341
Copper spacespace
Joined: August 17, 2002
Location: United States
Posted: March 19, 2016 at 6:15 AM / IP Logged Link to Post Post Reply Quote beegbie
Double check your security light cut. Db-all cuts it with the ORANGE / red, yellow/red. They list the wire color as blue/orange but I wouldn't trust colors . I would test and make sure the wire goes to ground every time the green light flashes.
syl20rochon 
Copper - Posts: 298
Copper spacespace
Joined: October 16, 2009
Location: Ontario, Canada
Posted: March 19, 2016 at 6:22 AM / IP Logged Link to Post Post Reply Quote syl20rochon
Did you cut the right security light wire? Also, the DBALL2 unit wire colors are hard to identify, color strips are weak compare to the surrounding of the wire, do you have the ones? ORANGE / Red and Yellow/Red. The ORANGE / Red is hard to read. What I would do first, I would cut one of them to leave the security light wire from the truck open to see if the green security light issue is solved. Also, I would check brake connection, is your remote starter shutting down when you press on the brake pedal? If not, when you insert the key, your truck's BCM is seeing 2 keys and that would be why the green key remains on and you would need to either, connect the brown brake input of the r/s to the brake pedal or W2W to the brake pedal output of the DBALL2 (grey on red connector), assuming that you made no connection and using the D2D option.
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
jvaguiar 
Member - Posts: 4
Member spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: February 07, 2016
Location: Texas, United States
Posted: March 28, 2016 at 11:02 PM / IP Logged Link to Post Post Reply Quote jvaguiar
Thanks you all. You guys went to the point.
I had inverted wires, YEL/RED X ORG/YEL. Now the green key go off when I insert the key.
Now another problem came up.
I am using a Avital 4103 with DBALL2 on D2D connection.
When I press start, the car never start at first time. It does at second tentative only. Any idea
Jose Aguiar
syl20rochon 
Copper - Posts: 298
Copper spacespace
Joined: October 16, 2009
Location: Ontario, Canada
Posted: March 29, 2016 at 5:35 AM / IP Logged Link to Post Post Reply Quote syl20rochon
Did you program your 4103 to tach mode? If so, did you learn tach input? Tach is taken by the DBALL2 on the CAN network and distributed to the 4103 on the D2D so no connection required.
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
jvaguiar 
Member - Posts: 4
Member spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: February 07, 2016
Location: Texas, United States
Posted: March 29, 2016 at 8:16 PM / IP Logged Link to Post Post Reply Quote jvaguiar
Thanks Syl20rochon;
there is no connection on 4103 in regarding the tach. The Dball2 has connection on CAN Network.
I really can't explain why it works on second tentative. Seem like at the first the communication between the 4103 and DBALL2 throught D2D is not well established yet, just a guess.
Jose Aguiar
syl20rochon 
Copper - Posts: 298
Copper spacespace
Joined: October 16, 2009
Location: Ontario, Canada
Posted: March 29, 2016 at 8:25 PM / IP Logged Link to Post Post Reply Quote syl20rochon
Hi, the 4103 is factory set to virtual tach, you have to change it in menu 2 to tach and learn the tach afterwards. This will solve your issue. The virtual tach in Directed product for the exception of the Autostart isn't reliable.
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Monday, January 17, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer