the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

SMD DD1 Distortion Light Solid Then Goes Out


Post ReplyPost New Topic
< Prev Topic Next Topic >
mohpro 
Member - Posts: 33
Member spacespace
Joined: October 30, 2014
Location: Maine, United States
Posted: June 07, 2016 at 4:44 PM / IP Logged Link to Post Post Reply Quote mohpro
I have 2 questions. Before I ask the questions, yes....I had all the head unit and amplifier settings on the appropriate levels before using the DD1 to detect distortion on the HU and set the gains on my amplifiers. My HU is Kenwood DNN992. I have 2 NVX 1200.1 amps and 1 NVX 800.4 amp. The HU pre-outs are 5V. I tested all RCAs and they read about 5.28V when the HU was at maximum undistorted volume. This is a lengthy post, but I know the more details the better. Thanks for any help. Here are my 2 questions...
1.) On the 4 channel amp, when setting the gain, the gain knob was turned about a little less than a 1/4 turn, then the distortion light on the DD1 came on a bright solid red, and stayed on if i turned the gain knob up anymore, so i backed it down to the point where the distortion light goes out. Gain set no problem. On my subwoofer amplifiers, when setting the gain, i would get the usual dim quick blinks of the distortion light as i turned the gain up. When i got to about the 3/4 point on the gain knob on my subwoofer amplifiers, the distortion light on the DD1 came on a bright solid red and stayed on for a good solid second or 2 then went out. I then continued turning the gain up, and there were no more quick blinks of the distortion light from the 3/4 point to the all the way up point, and the light never came back on solid either from the 3/4 to all the way up point. I used track 5, 40hz -10db. Out of curiousity, i used track 3 and i was also able to turn up the gain all the way without the distortion light staying lit, but with the solid one or two seconds of the light staying on before going out, and with track 3 this happened a little before the 3/4 point, which was where this happened when using track 5. What should I do, stop at the point where the light stays solid for a couple seconds then goes out, or turn the gain all the way up, since the distortion lihht does not come on when the gain is all the way up. Also, since the 4 channel amp and the subwoofer amps are all the same brand and series, all with the same voltage range on the gain knob, and all RCAs are getting 5V, shouldnt the gain of the subwoofer amps be right about where it is on the 4 channel amp?
2.) Should the AC voltage at the speaker outputs on the amplifiers match the voltage of the RCAs? My RCAs read about 5.28V AC, so is this what my speaker outputs on the amplifiers should read? If not, what should the speaker outputs voltage be?
i am an idiot 
Platinum - Posts: 13,488
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: June 07, 2016 at 11:31 PM / IP Logged Link to Post Post Reply Quote i am an idiot
It amplifies the voltage. The voltage coming out will be greater than the input voltage.

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Tuesday, January 18, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer