Upgrade Clifford LCD Remote To OLED

Tried search but still unclear. I want to know if I can upgrade my Clifford 330.3x LCD remote to the OLED remote if I also upgrade the antenna?

No, not according to the Directechs list. Having said that, I think it's only the antenna, the lead is the same. If you can obtain an antennna it's worthwhile plugging in the antenna then trying to pair the remote.

Depends on the Remote that you have! The 7941/7944 v/p/x and 7945v all work with the 6711t antenna. And is not compatible with the 6816t antenna (Which was replaced with the 6826t antenna). Your 3303v should have the 6211T antenna which will not work with a OLED SST Remote. The SST Remotes need the 6711T Antenna. The 6866T DS4(+) Antenna may work with the OLED SST Remotes but has not been tested to work so try at your own risk. 6711T antenna is compatible with any DEI remote that has a flashing Blue light or LCD and ends with FCC# EZSDEI 7941, 7944, 7945, 7752, 7652, 7754 Some older key fob transmitter remote original cases may also have the following: 800-274-0200 FCC ID: EZSDEI7941 FCC ID: EZSDEI7944 FCC ID: EZSDEI7945 FCC ID: EZSDEI7752 FCC ID: EZSDEI7754 FCC ID: EZSDEI7652 FCC ID: EZSDEI7941 V/P/X FCC ID: EZSDEI7944 V/P/X FCC ID: EZSDEI7945 V FCC ID: EZSDEI7752 V/P/X FCC ID: EZSDEI7652 V/P/X

I have also tested that the 6816T and its replacement 6826T antenna's and corresponding 1-Way remote 7656v and it does work with my 5601, and 5902 Alarms Brains(CPU) 6826T Antenna's date codes: OK/17B 5601(non 18-pin) date code: OK/9D 5902 (18-pin) date code: OK/9L The only issue I had was that I couldn't use the same 6826T antenna to program the same remote to both systems. Once the first antenna was used to program the remote to the 5601 it wouldn't program the remote to the 5902. When I used the 2nd 6826T I have on the 5902 with the same remote it programmed first try. Was only going for proof of concept, as I didn't enable the second car on the remote and try it that way with the same antenna on both. Car1 selection on the remote to 5601 and car 2 to 5902.

Thanks everyone. Can confirm it worked with just swapping the antenna to the 6711t using the same cable.

Good to hear!

So theoretically I could change my 5906 alarm to utilize a 5706 LCD remote by changing the antenna as well?

5906, 5706, 5806 and 5606 all use the same antenna. So no antenna change would be needed just program remote to system. you can enable 2nd car function on the remote "disabled " by default and use the same remote on both systems. Once you have 2nd car function enabled you need to switch to 2nd car on the remote then run the pairing to the second system. Barring any firmware changes by DEI to disable the functionality of the other remotes.

Calling lurch228, or anyone who might know. I also have an old Viper 5900 with the original lcd 2 way 7701 remote. I believe it is SST as well. I bought a nos color oled remote from a 7900 I think it is a 7541 remote. It will not pair to the 5900 but I am curious if there is any antenna upgrade for the 5900 to allow it to accept the 7900 oled remote (or even any of the newer 2 way remotes.) Thanks everyone!

5900 is SST-Keeloq antenna (6701T) coding and 7900 is ASK-Keelog antenna (6511t)coding. Too the best of my knowledge the the remote and antenna must match then it's trial and error to see what works. Just make sure that you delete all remotes from brain and antenna first then pull power from brain and then swap antenna. I had to program a 1-way remote before the 2-way remote would pair to the brain after a antenna swap from a 1-way antenna system to a 2-way antenna upgrade. At least that is what worked for me, at the time I didn't think to try zapping the brain with the bit-writer so can't say if that would also work . If you try it and it does please post your results to keep the learning moving forward.