2004 Toyota Tundra Regular Cab V6 Remote Starter Wiring

I am trying to get the wiring diagram to hook up a Compustar CM7200 to my 04 Tundra. I have no power locks or windows. All I need is a hood switch and some parking light indicators. I'm trying to get away with as few wires as possible and have a quality starter.   Also, I have both High Current and Low Current harnesses. I'm assuming it's one or the other? Any advice would be very welcome. I've done 2 others, but they all had immobilizers and T-harnesses, which took all of 15 minutes on my $runner and the Jeep Grand Cherokee maybe 60 min. This seems much more involved and Compustar does not give much help outside of the wiring harness diagram. SidFiguring it out, one project at a time

04 tundra is a basic car.. but you will need as a minimum .... 12V, Ground, Ign 1&2, Accessory, starter, brake, Tach and negative park lights. 12 VOLT CONSTANT     WHITE/RED (+)     @ IGNITION SWITCH HARNESS, WHITE 6-PIN PLUG, PIN 5      STARTER     WHITE/BLACK (+)     @ IGNITION SWITCH HARNESS, WHITE 6-PIN PLUG, PIN 4      STARTER 2     N/A           IGNITION 1     BLACK/RED (+)     @ IGNITION SWITCH HARNESS, WHITE 6-PIN PLUG, PIN 6      IGNITION 2     BLACK/YELLOW (+)     @ IGNITION SWITCH HARNESS, WHITE 6-PIN PLUG, PIN 2      IGNITION 3     N/A           ACCESSORY/HEATER BLOWER 1     PINK (+)     @ IGNITION SWITCH HARNESS, WHITE 6-PIN PLUG, PIN 3      ACCESSORY/HEATER BLOWER 2     N/A           KEYSENSE     N           PARKING LIGHTS ( - )     GREEN (-)     @ HEADLIGHT SWITCH, WHITE, 17-Pin Plug, Pin 14      PARKING LIGHTS ( + )     GREEN (+)     in DRIVERS KICK, WHITE 14-PIN PLUG, PIN B      POWER LOCK     See NOTE #3           POWER UNLOCK     See NOTE #3           LOCK MOTOR WIRE     N/A           DOOR TRIGGER     N/A           DOMELIGHT SUPERVISION     BLUE/BLACK (-)     @ BODY ECU, GRAY 18-PIN PLUG, PIN 8, See NOTE #2      TRUNK RELEASE     N/A           SLIDING POWER DOOR     N/A           HORN     BLACK/YELLOW (-)     @ HORN SWITCH, BLACK 12-PIN PLUG, PIN 6      TACH     WHITE/BLUE (AC)     @ ECM, Behind the GLOVE BOX, FAR RIGHT PLUG, pin 5      WAIT TO START LIGHT     N/A           BRAKE     GREEN/WHITE (+)     in DRIVERS KICK PANEL, WHITE, 14-Pin Plug, Pin L      FACTORY ALARM DISARM     DISARMS WITH UNLOCK           ANTI-THEFT     MAY BE EQUIPPED WITH TOYOTA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1

Thanks. I am assuming most of these are the high current wire from the harness with the larger gauge wires?Figuring it out, one project at a time

Found my answer. High Current at the ignition harness, so... yes, use high current wiring. But... I am not seeing the park light(-) anywhere in the CM7200 pinout diagram. I see "(+)12V Selectable by jumper (default parking light)"     Any help? Sid Figuring it out, one project at a time

https://www.staub.ca/pdf/sku/cm7200-ug.pdf CN5/17 (-250 ma) green/white- Light outMy ex once told me I have a perfect face for radio.

these wire colors do not match my regular cab V6, btw. My starter is Green/Black for example.Figuring it out, one project at a time

12volts      WHITE/ red (30A)      +   ignition harness     Starter       grn/blk (V6)      +   ignition harness     Ignition       BLACK/ red        +   ignition harness     Second Ignition       BLACK / YELLOW        +   ignition harness     Accessory       blue/red        +   ignition harness     Parking Lights+       green        +   driver kick harness to rear     Tach      black     AC rt side of motor, see below Figuring it out, one project at a time

Everything is wired except the tach wire and the parking lights. The gauge for the parking light from the high current harness is much larger than what I think is the parking light wire (green.) It's plugged in underneath. I am not sure what that looks like. I see no parking light wire on the other harnesses or noted in the wiring diagram for the CM7200. Any help would be greatly appreciated. SidFiguring it out, one project at a time

Thanks! I'll give that a shot. So the high current parking light wire (+)12V... omit? Cut it and tape it up? use the green/white from CN5 only? I'm learning but new to this stuff. SidFiguring it out, one project at a time