the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Semoic 433HZ Remote Programming?


Post ReplyPost New Topic
< Prev Topic Next Topic >
darth1 
Member - Posts: 3
Member spacespace
Joined: November 25, 2020
Location: Manitoba, Canada
Posted: February 16, 2021 at 2:31 PM / IP Logged Link to Post Post Reply Quote darth1
Has anyone used one of these? I bought one off Amazon.ca to play around with but I can't find how to program it anywhere. Of course it came with no paperwork at all!
https://www.amazon.ca/gp/product/B07RW3PH14/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
lectricguy 
Copper - Posts: 354
Copper spacespace
Joined: March 18, 2008
Location: Rhode Island, United States
Posted: February 16, 2021 at 7:19 PM / IP Logged Link to Post Post Reply Quote lectricguy
I've never used one of those, but looking at the pictures and reading the description (quite a poor translation), it appears to work as follows:
Hook up:
12VDC input is supplied to the 2 position green terminal. Polarity is shown on the PCB silkscreen on the bottom of the PC Board. The output appears to be a set of relay contacts on the 3 position green terminal, with contact locations silk screened on the PC Board: Normally Closed (NC-equivalent to pin 87A), Common (Com-equivalent to pin 30), and Normally Open (NO-equivalent to pin 87). Look at the 12Volt.com relay section for more detail.
Operation:
The relay is controlled by the included remote. It can be used in 1 of 3 modes:    jog/unlocked, Interlock/Lock, Auto Lock/Auto Lock
It appears that the modes operate as follows:
Jogging/unlocking, press and hold a button to activate the relay, release the same button to deactivate the relay.   (Channel switching requires a remote control button)
Auto lock: momentarily press a button to activate the relay, momentarily press the same button to deactivate the relay. (Channel switching requires a remote control button)
Interlock/Lock: Press one button to activate the relay, press another button to deactivate the relay. (One channel change requires 2 remote buttons)
Remote Programming:
1. Learning method: Press and hold the learning code button on the PC Board for 3 seconds. The indicator light will go out, then release the learning code button. Press any button on the remote control to send a signal, the indicator will flash 3 times, and then the method of learning success will be displayed normally.
2. Delete/Clear Method: Press the Learn button for about 8 seconds, the indicator will remain off, indicating that your saved information has been successfully deleted.
This is my best guess. Experiment with it and see what you find.
Lectric Guy

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, February 26, 2021 • Copyright © 1999-2021 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer