the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2002 Toyota Camry, Aftermarket Radio, Engine Noise


Post ReplyPost New Topic
< Prev Topic Next Topic >
tinker1982 
Member - Posts: 3
Member spacespace
Joined: September 17, 2021
Location: Tennessee, United States
Posted: September 17, 2021 at 2:37 PM / IP Logged Link to Post Post Reply Quote tinker1982
Hello i have a 2002 Toyota Camry my factory radio stopped working i ordered a radio that was totally different and my husband had to re wire the speaker wires now i have a bad engine noise coming from my speakers can u please help me
i am an idiot 
Platinum - Posts: 13,693
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: September 17, 2021 at 8:33 PM / IP Logged Link to Post Post Reply Quote i am an idiot
Did it have a gold JBL logo on the front of the radio? Did he purchase the appropriate wiring harness?
Is the volume of the music really loud at volume 5 or so?
tinker1982 
Member - Posts: 3
Member spacespace
Joined: September 17, 2021
Location: Tennessee, United States
Posted: September 18, 2021 at 12:58 PM / IP Logged Link to Post Post Reply Quote tinker1982
Yes it did the the jbl logo on it and yes it is very loud at 3 actually
i am an idiot 
Platinum - Posts: 13,693
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: September 18, 2021 at 7:42 PM / IP Logged Link to Post Post Reply Quote i am an idiot
With that system, if he is still using the JBL amplifier it requires getting signal from the RCA jacks, not the speaker wires of the new radio.
I am assuming he cut the plug off of the car's harness. He is going to have to get a short RCA cable, cut it in half. Strip it to expose the center conductor and the shield. Wherever he has the white pair of speaker wires connected, connect the center conductor of the RCA cable to where he had the solid white wire. Connect the shield to where the white/black. Connect that RCA to the front left RCA jack of the radio. Insulate the speaker wires.
Repeat for the other 3 channels. Grey = Front right. Green = Rear left. Purple = Right rear.
mgoetz74 
Silver - Posts: 424
Silver spaceThis member consistently provides reliable informationspace
Joined: February 15, 2012
Location: United States
Posted: September 20, 2021 at 3:23 PM / IP Logged Link to Post Post Reply Quote mgoetz74
make it little easier, take out the radio and look down to the brace under the radio. You should see 2 white plugs, these are the amp bypass plug. unplug them and use a metra 70-1761 harness. This will get rid of all the noise and prevent popping noise if you just use the rca ends like mentioned before. rca will work but you have to ground the factory amp with the deck to get rid of it and it doesn't always work. The amp is a 02 so it on borrowed time as is
33 years as a installer now just a retired old guy. Favorite thing to install/topic are remote starts/car alarms. Stop using test lights!!!
tinker1982 
Member - Posts: 3
Member spacespace
Joined: September 17, 2021
Location: Tennessee, United States
Posted: September 21, 2021 at 6:43 AM / IP Logged Link to Post Post Reply Quote tinker1982
Thank u very much this has been such a big help

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 10, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer