Few Aladdin 2000 Questions

Home / the12volt's Install Bay / Car Security and Convenience / Few Aladdin 2000 Questions (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

superthug

Member - Posts: 29

Joined: November 19, 2002

Location: United States

Posted: October 16, 2003 at 9:40 AM / IP Logged

I have the alarm installed already and it work great but here's few things I want to know more about.

1) How would I wire an air horn to work with the alarm?

2) I have a 91 integra 5-spd and I'm trying to put remote start. The white(?) wire from the aladdin brain supplies (-) charge, which wire by the clutch pedal should I connect to?

3) How can I buy another remote for my alarm? Just in case I lose mine.

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: October 16, 2003 at 2:33 PM / IP Logged

1. From the P10 harness use the BROWN wire and wire it to a 5 SPDT relay like so. This will convert the (-) signal of the BROWN wire to a (+) that you can wire up to the (+) on the air horn

2. Positive Clutch Bypass Circuit Negative Clutch Bypass Circuit

3. The remote controls are expensive because of the micro circuitry board and vibrator motor in them. Replacement remotes can be purcahsed through us.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

superthug

Member - Posts: 29

Joined: November 19, 2002

Location: United States

Posted: October 16, 2003 at 4:41 PM / IP Logged

2. How would I know which clutch bypass circuit I have? I have a 91 integra.

3. How much do the remote cost?

Thanks.

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: October 17, 2003 at 5:43 AM / IP Logged

2. You have a negative, but use the link above to test the circuit for sure. DO NOT ASSUME anything with vehicles as you might have a vehicle that for some reason is different than any other's

3. $ 109.00 USD

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

superthug

Member - Posts: 29

Joined: November 19, 2002

Location: United States

Posted: October 26, 2003 at 5:48 PM / IP Logged

I tried to get the remote start working and the parking lights just flash and the remote shows the car starting but nothing happens. I checked the dip switches, the brown loop is uncut and the tach is programmed fine. I even sat in the car and put the clutch down but it didnt start. The thing is when I press E and take the key out the car shuts off.

Also, the brain is not giving a ground anymore to the siren for some reason. The brown wire. I dont want to open everything up and check is there any other way I can hook up the siren to go off when the alarm goes off? Maybe use the parking light wire? Just a suggestion.

Need ur help Jeff, help me out man.

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: October 26, 2003 at 7:25 PM / IP Logged

You have two IGN wires to hook up, did you hook them both up ? Also, when you say " nothing happens" do you meant hat the car doesn't even attempt to turn over ? Make sure that you have the door trigger wire hooked up properly as well otherwise the remote start sequence will not work. YOu have to enter into ready mode in order for the remote starter to work at all.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

superthug

Member - Posts: 29

Joined: November 19, 2002

Location: United States

Posted: October 26, 2003 at 7:36 PM / IP Logged

I hooked up the 1st ignition wire (p6 yellow) and the other (p9 gray) one i had to convert the polarity of the alarm output to make it work. Yeah the car doenst attempt to turn over. The door trigger is working fine because when i arm the car it doenst say door open. Is there anything else i should check?

For the siren not working, I have an idea...I use the p3 yellow wire that goes to the parking lights. and use it to power the siren, air horn, and 4 strobe lights. Is it possible? how would i wire up the relays to work?

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: October 26, 2003 at 8:01 PM / IP Logged

Did you program the GRAY & the WHITE wires for the correct function as well ?

As far as the YELLOW wire for the light control, you can use relays and use the YELLOW wire as your trigger wire. Wire up the devices that require a (+) input to turn on with this relay configuration and for the devices that require a (-) input to turn on use this relay configuration

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Few Aladdin 2000 Questions

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.