1995 nissan 240sx engine start HELP!

Home / the12volt's Install Bay / Car Security and Convenience / 1995 nissan 240sx engine start HELP! (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

mr_timluu

Member - Posts: 12

Joined: July 27, 2002

Location: United States

Posted: July 28, 2002 at 12:30 AM / IP Logged

hi....love the site....i have a

CLIFFORD AVANTGUARD G4 w/ INTELLISTART

can anyone tell me where i am suppose to put a relay for the engine start. the car has to crank twice in order to start the engine and it causes an overcrank on the second time... there are i believe 2 IGNITION WIRES, 2 STARTER WIRES on the car, the intellistart has 2 IGNITION WIRES and 2 A/C HEATER WIRES and 1 STARTER WIRE....i was told to use a relay and dont know how to use it for the second ignition or the second starter or use resisters and diodes to a relay to prolong the starter signal to crank longer....if i want to do this..what kind of diodes and resisters or relay setup....i have been working on my engine start for 3 days with only little luck of starting the engine...

THANKS TO ANYONE AND EVERYONE WHO PROVIDES ANY INFO

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: July 28, 2002 at 8:41 AM / IP Logged

Nissan

240SX

1995

Remote Starter Wiring Colors and Notes
Function		Vehicle Color	Location
Start:		BLACK / YELLOW	IGNITION SWITCH HARNESS
Ignition #1:		BLACK/ RED	IGNITION SWITCH HARNESS
Ignition #2:		WHITE	IGNITION SWITCH HARNESS
Ignition #3:		N/A
Accessory:		WHITE/ BLUE	IGNITION SWITCH HARNESS
Brake Light:		RED / GREEN (+)	SWITCH ABOVE BRAKE PEDAL
Tach Signal:		YELLOW/RED	PIN 3 AT ECCS *
Parking Lights:		RED / BLUE	(+) AT HEADLIGHT SWITCH
Headlights:		SEE NOTES BELOW	**
OEM Alarm Disarm:		GREEN/ YELLOW (-)	SAME CONNECTOR AS DOORLOCKS
OEM Alarm Arm:		N/A
Diesel Glow Plug:
Clutch Bypass Wire:
Notes:	* Electronic Concentrated Control System (ECCS) Module Located In Pasenger Kick Panel. Pin #2 Is Also YELLOW/RED Tach Wire. These Wires Are On Short Side Of Connector Near Center Bolt. LT. GREEN/ BLUE At Distributor Is High Signal. ** This Vehicle Is Equipped With Two Start Wires. Both Must Be Powered In Order For Vehicle To Start When Engine Is Cold

Nissan

240SX

1995

Alarm and Keyless Entry Wiring Colors and Notes
Function		Vehicle Color	Location
Constant +12 Volts:		WHITE	IGNITION SWITCH HARN.(WHT/RED FOUND)
Starter Kill:		BLACK / YELLOW	IGNITION SWITCH HARNESS
Ignition +12 Volts:		BLACK/ RED	IGNITION SWITCH HARNESS
Dome Lights/Superv:		RED / WHITE	(-) DRIVER KICK PANEL ***
OEM Horn:		GREEN / WHITE (-)	STEERING COLUMN HARNESS OR AT RELAY
Power Lock:		LIGHT GREEN / WHITE	@ WHITE 12 PIN CONN. IN DR. KICK ****
Power Unlock:		BROWN / RED	@ WHITE 12 PIN CONN. IN DR. KICK ****
Trunk Release:		N/A
Alarm Input Wire:		RED / WHITE	(-) DRIVER KICK PANEL ***
Notes:	* SE Models Are Diode Isolated. Wire In Bottom Row Of Main Body Harness Conn. In Driver Kick Panel. Proper Wire On Base Model Is BLUE. ** Negative Pulse Door Lock

The starter wire you must run in two wires and connect to one on the starter module on the Clifford.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

mr_timluu

Member - Posts: 12

Joined: July 27, 2002

Location: United States

Posted: July 28, 2002 at 1:25 PM / IP Logged

i looked up the wire diagram in a recent post and already have this info........there is one starter wire coming from the clifford intellistart......and the nissan has 2 starter wires.....how do i hook up this one wire to 2 starter wires...do i hook up to the key side or coil side or tap or splice a wire..

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: July 28, 2002 at 1:44 PM / IP Logged

What you have to do is solder 2 wires onto the Clifford starter wire and then take one of each and attach to each starter wire. That's it, your done.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

mr_timluu

Member - Posts: 12

Joined: July 27, 2002

Location: United States

Posted: July 28, 2002 at 11:28 PM / IP Logged

thanks...

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: July 29, 2002 at 8:12 AM / IP Logged

no problemo 1995 nissan 240sx engine start HELP! - Last Post -- posted image.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

1995 nissan 240sx engine start HELP!

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.