95 grand prix remote starter

Home / the12volt's Install Bay / Car Security and Convenience / 95 grand prix remote starter (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

muaiad97

Copper - Posts: 207

Joined: April 08, 2003

Location: Canada

Posted: December 16, 2003 at 8:53 PM / IP Logged

hello all

i have grand prix 95 i installd the remote starter with bypass moduel # 791.

it,s working good but i have problem the car is not runing with the key but its working with the remot starter. please anyone can help me with that .

ck auto

Copper - Posts: 257

Joined: September 20, 2003

Location: Canada

Posted: December 16, 2003 at 9:04 PM / IP Logged

hi make sure you have power on all ign wires when key is in ign maybe you pulled wire out of plug or blew fuse

good luck

kirk

muaiad97

Copper - Posts: 207

Joined: April 08, 2003

Location: Canada

Posted: December 16, 2003 at 9:18 PM / IP Logged

thank you

i cheked every wire they are ok but i mean mybe its the security.

because ther is no crank with the key but the car working with remot starter

ck auto

Copper - Posts: 257

Joined: September 20, 2003

Location: Canada

Posted: December 16, 2003 at 9:39 PM / IP Logged

did you maybe hook up your bypass wrong try taking bypass out and see if it starts

good luck

kirk

chriswallace187

Gold - Posts: 1,661

Joined: March 11, 2002

Location: Pennsylvania, United States

Posted: December 16, 2003 at 9:47 PM / IP Logged

Check how you hooked up the VATS wires. I've never done a 791, but I assume in this hookup you had to cut one of the two VATS wires, and hook the wires from the bypass module up as such - one wire gets spliced into the uncut VATS wire, one goes to the key side of the cut wire, and one goes to the PCM side. If the key side has the incorrect or no wire hooked up to it, it would cause the problem that you're having.

Search for other posts by chriswallace187

muaiad97

Copper - Posts: 207

Joined: April 08, 2003

Location: Canada

Posted: December 16, 2003 at 10:20 PM / IP Logged

thank you all

i took out the remot starter of the car to see the car will work.but still dosnt work with the key.befor i install the remot starter the car was working with the key.but now is not only with remot starter working.

muaiad97

Copper - Posts: 207

Joined: April 08, 2003

Location: Canada

Posted: December 17, 2003 at 4:25 PM / IP Logged

grand prix 95 please i need help.help

before i install remot starter the car was working very good.

after i installd remot starter the car still working good but only with the remot starter. with the key ther is no crank all ligths comes on and the dash too but no crank. the starter is bulldog and the bypass moduel is 791.

please help

sparkie

Platinum - Posts: 2,061

Joined: November 06, 2003

Location: Canada

Posted: December 17, 2003 at 7:07 PM / IP Logged

The problem you describe is likely caused by the way the bypass is hooked up. For a better and easier method, measure the resistance of the resistor in the body of your key with a meter. Measure from one side of the key to the other. Get a resistor of this value and a relay. Wire the relay as follows:

Pin # 85 to the ground out when running of the remote starter.

Pin # 86 to ignition (pink in the car's ignition harness)

Pin # 87a to the cut side of the VATS wire (key side) - This is one of the two small white wires sheathed in the orange or black wrap.

Pin # 30 to the other side of the cut VATS wire

Pin # 87 to the resistor and then to the uncut VATS wire.

With this set up you don't need your bypass and the integrity of the VATS system stays intact. The relay and resistor should be available at most electrical supply stores or stereo shops.

sparky

muaiad97

Copper - Posts: 207

Joined: April 08, 2003

Location: Canada

Posted: December 17, 2003 at 8:07 PM / IP Logged

Thank you for ur help. but the problem is i took out the remot starter of the car to see the car will start but still ther is no crank and i put back all the wires like befor i install the remot starter.with the key it dosnt work.

muaiad97

Copper - Posts: 207

Joined: April 08, 2003

Location: Canada

Posted: January 16, 2004 at 7:42 PM / IP Logged

hi all i am trying to bypass the securety in grand prix the mesurment in the key says 9.53 kom.i cant find that valu can i use closer to that number

thanx for help

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.