2002 chrysler voyager starter

Home / the12volt's Install Bay / Car Security and Convenience / 2002 chrysler voyager starter (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

nkennedy

Member - Posts: 5

Joined: January 07, 2004

Location: United States

Posted: January 07, 2004 at 4:46 PM / IP Logged

Newbie!!! I am installing an audiovox remote starter for my wife. I have already read the previous posts but her is my problem. Coming from the remote start unit I have the following wires connected:

Starter Harness | Vehicle

RED / White (Bat 1) Battery

Red (Bat 2) Battery

Yellow (Start) yellow

Blue (IGN 1) pink/white

Green (IGN 2) -------------

Purple (Acc) -------------

------------------- PURPLE / brown (Second starter)

How do I tie in the second starter wire and to what wire. I already have the relay sitting in front of me?

Bnluis

Silver - Posts: 578

Joined: December 24, 2002

Location: New York, United States

Posted: January 07, 2004 at 5:34 PM / IP Logged

2002 chrysler voyager starter -- posted image.

Luis

Sound Waves

Is up to the installer to test all wires with a DMM whenever possible.

nkennedy

Member - Posts: 5

Joined: January 07, 2004

Location: United States

Posted: January 07, 2004 at 6:16 PM / IP Logged

I have the AA-RS30CS Model.

Is the PURPLE / brown wire just activated during start.

Does the yellow starter wire go to the relay? Do I leave the green IGN 1 wire loose? Is the resistir supposed to be grounded from relay position #87?

Just yell if I am a pain!

Thanks, Nick

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 08, 2004 at 2:42 AM / IP Logged

The 2nd starter is only active during remote start just like the primary starter wire. The Starter wire does go to a relay ( not sure where though ) Leave the GREEN and the PURPLE wires as they are not used for this vehicle. You have to add a relay for the 2nd starter wire as shown above and the resistor goes on pin 30 and pin 87 is to ground. When the relay is activated , pin 30 and 87 connect sending a ground signal with a 180 ohm signal to the 2nd starter wire.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

nkennedy

Member - Posts: 5

Joined: January 07, 2004

Location: United States

Posted: January 08, 2004 at 10:32 AM / IP Logged

Thank you, that clears a lot of things up!

Nick

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

2002 chrysler voyager starter

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.