2001 Ford Ranger remote start

Home / the12volt's Install Bay / Car Security and Convenience / 2001 Ford Ranger remote start (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

p71-cruiser

Member - Posts: 47

Joined: January 07, 2004

Location: United States

Posted: January 07, 2004 at 11:52 PM / IP Logged

Hello

I have a 2001 Ford Ranger manual .

Does this truck have a netural switch to tell that it is in netural?

If it does what wire color, location and pos or neg switching

Thanks for the help

P71-Cruiser

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: January 08, 2004 at 5:55 AM / IP Logged

this is all i have on that truck:

Neutral Safety NONE GROUNDING TYPE - OEM SWITCH OPENS STARTER CIRCUIT.

i dont color or location..

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

p71-cruiser

Member - Posts: 47

Joined: January 07, 2004

Location: United States

Posted: January 10, 2004 at 12:06 PM / IP Logged

Could I get a 2001 Ford ranger wiring Digaram inc the clutch bypass wire

Thanks

p71-cruiser

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: January 10, 2004 at 1:36 PM / IP Logged

Make: Ford

Model: Ranger

Year: 2001

This Database Was Last Updated On: 6/9/2003

Index #: 1880

Alarm

Constant 12 volts YELLOW (4) IGNITION SWITCH HARNESS

Ignition 12 volts L GREEN/ VIOLET IGNITION SWITCH HARNESS

Starter RED / L BLUE IGNITION SWITCH HARNESS

Dome Light BLACK/ L BLUE (+) LARGE WIRE HARNESS ABOVE GAS PEDAL *

Trunk Pin Switch N/A

Parking Lamp BROWN (+) AT HEADLIGHT SWITCH

Power Lock PINK / YELLOW 16 PIN CONNECTOR IN #201

Power Unlock PINK/L GREEN DRIVER KICK PANEL

* BLACK/ BLUE (+) In Same Connector Is Domelight Relay Output And Works Same As BLACK/ PINK (+). BLACK/ BLUE Also Found At Courtesy Light Relay Under Passenger Dash Behind Glove Box On Glove Box Bracket. #201- See Negative Pulse Door Lock Diagram.

Remote Start

Tach Signal TAN / YELLOW AT POWERTRAIN CONTROL MODULE * #239

Ignition #2 GRAY / YELLOW IGNITION SWITCH HARNESS #235

Ignition #3 N/A

Accessory BLACK/ L GREEN IGNITION SWITCH HARNESS

Neutral Safety NONE GROUNDING TYPE - OEM SWITCH OPENS STARTER CIRCUIT

Brake Light L GREEN (+) AT SWITCH ABOVE PEDEL

Reverse Light BLACK/ PINK (+) ON DRIVER SIDE OF TRANSMISSION

Rear Window Defrost N/A

#235- See Powering Extra Ignitions Diagram. #239 - See Immobilizer Bypass Diagram. *The Powertrain Control Module Is On The Top Of The Firewall Under The Hood Towards The Passenger Side. The Tachometer Wire Is In Pin 48.

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

p71-cruiser

Member - Posts: 47

Joined: January 07, 2004

Location: United States

Posted: January 10, 2004 at 2:23 PM / IP Logged

Thanks David

One more question

I'm putting a remote start on my manual transmission Ranger.

How do I bypass the clutch safety switch (the switch that makes sure the clutch pedal is depressed before starting the truck)?

Or does the remote start bypass this switch?

Thanks again for any help

profuse007

Gold - Posts: 2,015

Joined: October 20, 2002

Location: Texas, United States

Posted: January 10, 2004 at 2:30 PM / IP Logged

if you check the clutch at the switch, test the wires coming off it. see which one need what, either neg or pos.

Houston,TX

"The two most common elements in the universe are H+ and stupidity" (Ellison).

p71-cruiser

Member - Posts: 47

Joined: January 07, 2004

Location: United States

Posted: January 10, 2004 at 4:02 PM / IP Logged

7 wires? 2001 Ford Ranger remote start -- posted image.

That's a lot of testing

p71-cruiser

Member - Posts: 47

Joined: January 07, 2004

Location: United States

Posted: January 11, 2004 at 9:12 PM / IP Logged

2001 ford ranger

I have two different wiring digrams that tell me that I have ignition 3 and I do not have ign 3 can you please tell me the on which one to use?

Also on my remote start I have the

accessory wire

starter wire

ign 1 wire

ign2 wire

ign3 wire

Just to be sure that I got it right can you tell me which wire goes from the remote start to the truck's starter wires

Thanks for the help

p71-cruiser

Basscoholic23

Copper - Posts: 67

Joined: June 11, 2003

Posted: January 11, 2004 at 10:17 PM / IP Logged

Gray / YELLOW would be your 2nd ignition

if you have more than one gray / YELLOW then that would be your 3rd ignition.

Yor remote starter wire would go to your RED / light blue wire in your factory harness of your truck.

mazdatruckin

Copper - Posts: 69

Joined: September 10, 2003

Posted: January 12, 2004 at 10:59 AM / IP Logged

its funny tho how 2nd ign is defined.

They gray / YELLOW comes on in the ign posistion, but dies out during cranking, so it's safe to power the wire as an accessory wire.

Also the 2 gray / YELLOWs are common thru the switch so you only need to power one of them.

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.