02 caravan remote start

Home / the12volt's Install Bay / Car Security and Convenience / 02 caravan remote start (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

Irnotslow

Member - Posts: 45

Joined: October 06, 2003

Location: United States

Posted: March 12, 2004 at 9:54 PM / IP Logged

I am going to install an add on Remote Starter on a 2002 Dodge Caravan. The RS I am installing an add-on type unit. It uses either 1 or 2 negitive pulses to activate the stat sequence. I have a few questions: 1) i looked at the wiring for this van....

Factory Disarm

WHITE/ Dark Green

(665 Ohm) left Connector bottom of Fuse Panel

how do I wire this?

2) also I need the lock or unlock wire motor circut.... to trigger the starter

Door Lock	WHITE/ Dark Green (-)	BCM at Fuse Panel 1500 Ohm Resistor
Door Unlock	WHITE/ Dark Green (-)	White Connector B58 Connector 250 Ohm Resistor
Driver's Lock	Brown (+)	Junction Block
Driver's Unlock	Purple / YELLOW (+)	Junction Block

again how do i wire this?

3) Lastly Does this van have a factory anti-theft system? My research says no

thank you in advance

irnotslow

daniel2002p

Silver - Posts: 524

Joined: October 10, 2003

Location: United States

Posted: March 14, 2004 at 9:09 AM / IP Logged

what kind of add on RS are you installing?? Stand alone that required 2 lock pulses to activate or a addon to a security system.

2005 Toyota Corolla S

1.8L VVT-i I-4

Always double check your wires with a DMM!!!

Do Not Use A Test Light!!!

MECP Certified Installer!

Best Buy 665 - IN IT TO WIN IT! TEAM MOBLE!

Irnotslow

Member - Posts: 45

Joined: October 06, 2003

Location: United States

Posted: March 14, 2004 at 10:38 AM / IP Logged

it is a 20022 from www.autocommand.com (designtech). It is an addon. once all the required wiring is finished, you then need to find a neg pulse (lock or unlock) does not matter, My question is must I hook up the factory alarm disarm>>>

Factory Disarm

WHITE/ Dark Green

(665 Ohm) left Connector bottom of Fuse Panel

and how do wire that?

And two which wire do i use for the lock or unlock pulse, if need be i will use a reversing relay

Door Lock	WHITE/ Dark Green (-)	BCM at Fuse Panel 1500 Ohm Resistor
Door Unlock	WHITE/ Dark Green (-)	White Connector B58 Connector 250 Ohm Resistor
Driver's Lock	Brown (+)	Junction Block
Driver's Unlock	Purple / YELLOW (+)	Junction Block

I am assuming i can instal a reversing relay on the Brown or the PURPLE / Yellow wire, because it will unlock/lock thru the factory FOB.

irnotslow

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

02 caravan remote start

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.