bad install?

Home / the12volt's Install Bay / Miscellaneous - Off Topic / bad install? (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

Teken

Gold - Posts: 1,492

Joined: August 04, 2002

Location: Aruba

Posted: March 26, 2004 at 5:38 PM / IP Logged

LMFAO ... I have to see this every week-end. bad install? - Page 2 -- posted image.

Regards

EVIL Teken . . .

defective

Silver - Posts: 642

Joined: August 20, 2003

Location: Canada

Posted: April 05, 2004 at 10:40 AM / IP Logged

btw... is Tim on our board? I always wonder where these guys like Rivera and Baille chat it up.

Ravendarat

Platinum - Posts: 2,806

Joined: February 23, 2004

Location: Canada

Posted: April 05, 2004 at 5:28 PM / IP Logged

As far as I know Tim isnt on his board. Too Bad to cause the guy knows his stuff and can answer just about any question you can think of.

double-secret reverse-osmosis speaker-cone-induced high-level interference distortion, Its a killer

DYohn

Moderator - Posts: 10,741

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

Joined: April 22, 2003

Location: Arizona, United States

Posted: April 10, 2004 at 10:47 PM / IP Logged

Priceless.

Support the12volt.com

evolutionoftym

Member - Posts: 39

Joined: January 06, 2004

Location: United States

Posted: April 14, 2004 at 5:35 PM / IP Logged

For everything else....There's Mastercard.....

Search for other posts by evolutionoftym

flynntech

Copper - Posts: 275

Joined: April 15, 2004

Location: United States

Posted: April 23, 2004 at 3:38 AM / IP Logged

The most disturbing one was the 'crowd' of people checking out the messy wires......that's creepy!

The sad part is...some of that stuff isn't too unusual in pro shops. The place I worked at had some real idiot installers and even if you were a good installer, they expected you to do everything fast. I've hooked up a couple of alarms with full length wires and ziptied it all up under the dash.....'never to be seen again' It worked and funtioned properly, but I didn't take a second to make it look pretty. The fact that my previous paychecks were short by about $100 each time didn't help the situation either.....

Ravendarat

Platinum - Posts: 2,806

Joined: February 23, 2004

Location: Canada

Posted: April 26, 2004 at 4:02 PM / IP Logged

I can honestly say I have never been in a big enough hurry that I couldnt cut the wires to lenghth and make it look nice. If you see my installs on allarms and staters then you will see every wire taped full length so it blends in and everything is zip tied up. Now the last guy that worked there, well thats a whole new conversation

double-secret reverse-osmosis speaker-cone-induced high-level interference distortion, Its a killer

jim hines

Member - Posts: 2

Joined: April 27, 2004

Location: Canada

Posted: April 27, 2004 at 5:34 PM / IP Logged

looking for a wiring diagram for 89 nissan pulsar fuse panel

jim hines

Member - Posts: 2

Joined: April 27, 2004

Location: Canada

Posted: April 27, 2004 at 5:38 PM / IP Logged

have lost power to half the fuse panel on 89 pulsar

anyone got a wiring diagram

someone help!!!!!!!!!!! please!!!!!!!!!

jim hines

hzemall

Copper - Posts: 55

Joined: May 26, 2004

Location: Canada

Posted: May 26, 2004 at 4:20 PM / IP Logged

Hey all, just joined the board and I thought I would pop in and say "hey"

Tim Baillie

Installer/Designer/Fabricator

Certified Autosound & Security

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.