the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2003 Dodge Stratus wiring diagam ,etc.


Post ReplyPost New Topic
< Prev Topic Next Topic >
kslamm 
Member - Posts: 1
Member spacespace
Joined: June 27, 2004
Location: United States
Posted: June 27, 2004 at 8:22 PM / IP Logged  
Looking for a wiring diagram for a 2003 Dodge Stratus,any help would be gratly appreciated.Also anybody know  the best possible way to hook up the remote turn on from my amp?Was not sure if the factory 4 disc changer that are in the Stratus' have a wire to splice into or if I need another alternative?Thanks.    
jfk51502003 
Copper - Posts: 221
Copper spacespace
Joined: March 04, 2004
Location: United States
Posted: July 01, 2004 at 2:22 PM / IP Logged  
DIRECTWIRE™ WIRING INFORMATION - DODGE / STRATUS SEDAN / 2003 / Remote Start
[PRINT THIS PAGE]
12voltspink/black & red + ignition harness
Starteryellow + ignition harness
Second StarterN/A
Ignitionblue + ignition harness
Second IgnitionGREEN/ red (20 awg) + ignition harness
Third Ignition
AccessoryBLACK/ orange + ignition harness
Second AccessoryBLACK/ white + ignition harness
Keysense
Power LockWHITE/ green + conn. C4, pin 15 @ BCM
Notes: Lock requires a positive trigger thru a 1800 ohm resistor. Unlock requires a positive trigger thru a 750 ohm resistor. MUST use relays.
The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Power Unlocksame wire as power lock
Lock MotorORANGE / black 5wiconn. C4, pin 9 @ BCM
Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Unlock Motorblue/white 5wiconn. C4, pin 13 @ BCM
Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Parking Lights+BLACK / YELLOW + headlight switch or DKP
Parking Lights-
Hazards
Turn Signal(L)
Turn Signal(R)
Reverse Light
Door Trigger - conn. C4 @ BCM
Notes: The driver door trigger is tan in pin 5, the front passenger door is tan/red in pin 6, the left rear door is tan/orange in pin 7, and the right rear door is tan / YELLOW in pin 8. Use all four wires and diode isolate each.
The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Dome Supervisionuse door trigger
Trunk/Hatch Pintan/black - conn. C4, pin 18 @ BCM
Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Hood Pin
Trunk/Hatch ReleaseBLACK/ white 5wiconn. C4, pin 1 @ BCM
Notes: The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Power Sliding DoorN/A
Factory Alarm Armlt. GREEN/ orange + conn. C4, pin 4 @ BCM
Notes: Arm requires a positive trigger thru a 1800 ohm resistor. Disarm requires a positive trigger thru a 750 ohm resistor. MUST use relays.
The BCM (Body Control Module) is attached to the fuse/relay box at the end of the dash on the driver side. Connector C4 is a 26 pin plug on the bottom edge of the BCM.
Factory Alarm Disarmsame wire as alarm arm
Disarm No Unlocksee factory alarm disarm
TachometerNOT GREEN/ lt. green ac any ign. coil or fuel injector
Wait to startN/A
Brake WireWHITE/ tan + brake pedal switch
Parking Brake
Horn TriggerBLACK/ red - steering column
Memory Seat 1
Memory Seat 2
Memory Seat 3
2003 Dodge Stratus wiring diagam ,etc. - Last Post -- posted image.
Immobilizer Bypass Module:Required: YesType: Sentry KeyPart #: 555C, 556U, or 555U
Notes: Only vehicles with gray keys have the immobilizer.
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, June 14, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer