Alarm install 94 4runner

Home / the12volt's Install Bay / Car Security and Convenience / Alarm install 94 4runner (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

Prophit

Copper - Posts: 79

Joined: March 04, 2004

Location: United States

Posted: September 26, 2004 at 1:32 PM / IP Logged

Im about to start installing my alarm into my 4runner and wanted to ask if the factory alarm will need to be either disabled or uninstalled? I found the module underneith my seat. Im thinking i can use alot of those wires to tap into for the install. Also im a little confused on the starter kill I have an fm2009 alarm and it already was wired into a car. So there are some relays already but im not quite sure i know what im doing. If someone could just help me with the wiring i would be ready to go.

1994 4 runner

FM 2009 Alarm with remote start.

Please help!!

Prophit

Copper - Posts: 79

Joined: March 04, 2004

Location: United States

Posted: September 26, 2004 at 9:02 PM / IP Logged

About to finish my install on my 4runner and just doing some research on either to go tachless or install the tach cable. The directions i have found tell me its a black cable at the diags box. I checked and its inside of like 2 differect heat shrink covers. I can take that off but is it worth it?

Please assist. Thanks

Teken

Gold - Posts: 1,492

Joined: August 04, 2002

Location: Aruba

Posted: September 26, 2004 at 9:05 PM / IP Logged

Tach is the only tried and true method to ensure a consistent RS, each time.

Regards

EVIL Teken . . .

snguyen

Silver - Posts: 281

Joined: October 09, 2003

Location: United States

Posted: September 26, 2004 at 9:12 PM / IP Logged

Try this https://www.the12volt.com/installbay/vehicles.asp

Prophit

Copper - Posts: 79

Joined: March 04, 2004

Location: United States

Posted: September 26, 2004 at 10:42 PM / IP Logged

Ok well then where should i tap in at.. Should I couse a coil? or go in where the distribtor is?But going through where the wiring diagram says is hard.

Prophit

Copper - Posts: 79

Joined: March 04, 2004

Location: United States

Posted: September 27, 2004 at 10:10 AM / IP Logged

Got my alarm finally installed but i have noticed that the siren is not working. I took this alarm out of another car that i didnt install. I found that they are using a relay for the siren. Is that needed?

Its an fm2009 alarm. Please help. Thanks

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: September 27, 2004 at 10:27 AM / IP Logged

Probably used relays because it had more than a couple of sirens hooked up to the siren wire. Check the output of the siren wire to see if your getting a current from it.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

Prophit

Copper - Posts: 79

Joined: March 04, 2004

Location: United States

Posted: September 27, 2004 at 10:45 AM / IP Logged

Ya there was 2 sirens hooked up but im only using one. I will check that later. If i just use the one do i need to use relays?

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: September 27, 2004 at 10:58 AM / IP Logged

If you just use one, then you don't need a relay.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Prophit

Copper - Posts: 79

Joined: March 04, 2004

Location: United States

Posted: September 27, 2004 at 12:44 PM / IP Logged

So i have a 94 4 runner. Directions say to use the black cable at the diags box. Well that cant be done. So whats another place to do this at? Maybe at the distriboter or something?

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.