2004 Toyota Sienna Wire Diagram Needed

Home / the12volt's Install Bay / Car Security and Convenience / 2004 Toyota Sienna Wire Diagram Needed (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

newinstaller

Copper - Posts: 160

Joined: July 11, 2004

Location: Canada

Posted: October 13, 2004 at 7:29 PM / IP Logged

Hi,

I am looking for a 2004 Toyota Sienna Wire Diagram.

I am installing a Compustar 2WFMAS Alarm/Starter

Any help would be great

Anyone Got DEI??

Thanks

snguyen

Silver - Posts: 281

Joined: October 09, 2003

Location: United States

Posted: October 13, 2004 at 7:31 PM / IP Logged

Toyota

Sienna

2004-2004

Remote Starter Wiring Colors and Notes
Function	Vehicle Color	Location
Start:	BLACK / YELLOW	IGNITION SWITCH HARNESS *
Ignition #1:	Black	IGNITION SWITCH HARNESS
Ignition #2:	BLACK / YELLOW	IGNITION SWITCH HARNESS
Ignition #3:	Blue/Black (-)	Use Key Sense wire to disarm the OEM factory alarm. **
Accessory:	Pink	IGNITION SWITCH HARNESS
Brake Light:	GREEN / WHITE (+)	Above the brake switch
Tach Signal:	BLACK/ Orange	ECM located behind the glovebox
Parking Lights:	GREEN/ Black (-)	Headlight Switch
Headlights:	N/A
OEM Alarm Disarm:	Key Sense Wire
OEM Alarm Arm:
Diesel Glow Plug:
Clutch Bypass Wire:
Notes:	This Vehicle is equipped with Transponder Theft System. Use Universal Alarm Bypass Module part #2x402 where X can be any number. *Use the WHITE/ Black IGN3 wire from the unit to disarm the alarm. The key sense wire will measure a ground while the key is in the ignition switch.

Toyota

Sienna

2004-2004

Alarm and Keyless Entry Wiring Colors and Notes
Function	Vehicle Color	Location
Constant +12 Volts:	WHITE/ Blue (+)	Ignition Switch Harness
Starter Kill:	BLACK / YELLOW	IGNITION SWITCH HARNESS *
Ignition +12 Volts:	Black	IGNITION SWITCH HARNESS
Dome Lights/Superv:	See Note Below ***	See Note Below***
OEM Horn:	GREEN/ Black (-)	Below the steering column
Power Lock:	Lt. Green (-)	Drivers kick panel
Power Unlock:	Blue (-)	Drivers kick panel
Trunk Release:	Yellow/Red (-)	Fuse Box Below drivers kick panel
Alarm Input Wire:	See Note Below ***	See Note Below***
Notes:	*** The vehicle has individual door triggers. Driver's door RED / Yellow(-),The drivers door and the passengers share the same wire. The left sliding door is gray (-). Right sliding door RED / white. These wires will be located at the BECU module located at the fuse box in the driver's kick panel.

newinstaller

Copper - Posts: 160

Joined: July 11, 2004

Location: Canada

Posted: October 13, 2004 at 7:34 PM / IP Logged

is this DEI?

Thanks

snguyen

Silver - Posts: 281

Joined: October 09, 2003

Location: United States

Posted: October 13, 2004 at 7:34 PM / IP Logged

SIENNA 2004
WIRE	COLORS	LOCATION
12 VOLTS CONSTANT	WHITE/ RED and WHITE/ BLUE	IGNITION SWITCH HARNESS
IGNITION 1	BLACK (+)	IGNITION SWITCH HARNESS
IGNITION 2	BLACK / YELLOW (+)	IGNITION SWITCH HARNESS
ACCESSORY /HEATER BLOWER	PINK (+)	IGNITION SWITCH HARNESS
STARTER	BLACK / YELLOW (+)	IGNITION SWITCH HARNESS
PARKING LIGHTS (-)	GREEN/ BLACK (-) See NOTE *	@ HEADLIGHT SWITCH
DOME LIGHT	RED / GREEN (-)	@ INTERIOR LIGHT SWITCH ON DASH
POWER DOOR LOCK	LIGHT GREEN See NOTE **	IN DRIVERS KICK PANEL, in an 18 Pin Plug (TYPE B)
POWER DOOR UNLOCK	BLUE See NOTE **	IN DRIVERS KICK PANEL, in an 18 Pin Plug (TYPE B)
TRUNK RELEASE	YELLOW/RED (-)	@ BOTTOM LEFT of FUSEBOX 22 Pin Plug
TACH SENSOR	BLACK/ ORANGE NOTE ***	@ ECM, Connector E4, Pin 5
BRAKE	GREEN / WHITE (+)	@ SWITCH ABOVE BRAKE PEDAL
HORN	GREEN/ BLACK (-)	@ STEERING COLUMN HARNESS
FACTORY DISARM	disarms with Unlock
FACTORY ANTI-THEFT	TRANSPONDER	Requires #791 Bypass Module and Extra Ignition Key

NOTE * You CANNOT USE any (+) Positive Parking Light circuit on this vehicle, you MUST use the (-) Negative Parking light circuit and this will require an extra Relay Part # 775, to order contact: DIRECT WHOLESALE at 1-800-659-0764.

NOTE ** These 2 wires will ONLY meter (show a Ground or (-) Negative) when you place a key in the DRIVERS DOOR KEY CYLINDER (outside of drivers door) and rotating from Lock to Unlock. You must use a Double Pulse Unlock programming on this vehicle. For a Single Pulse Unlock you can use the wire in the Passengers kick panel in a 12 Pin Plug, it will meter off of the Passengers key cylinder, the wire is a BLUE / YELLOW (-).

NOTE *** The ECM is located behind the Glovebox.

newinstaller

Copper - Posts: 160

Joined: July 11, 2004

Location: Canada

Posted: October 13, 2004 at 7:37 PM / IP Logged

thanks so much buddy

your the best

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

2004 Toyota Sienna Wire Diagram Needed

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.