the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2002 Maxima Wiring


Post ReplyPost New Topic
< Prev Topic Next Topic >
Jediknight1274 
Member - Posts: 4
Member spacespace
Joined: November 14, 2004
Location: United States
Posted: November 14, 2004 at 7:42 PM / IP Logged  

Hey out there, I'm looking for vehicle security wiring on the 02 Maxima SE including all of the automation wiring for the factory power window mods.  Locations and any tips would be great.

Thanks

SMCinMD
shadowinfector 
Copper - Posts: 199
Copper spacespace
Joined: October 02, 2003
Posted: November 14, 2004 at 7:45 PM / IP Logged  
DIRECTWIRE™ WIRING INFORMATION - NISSAN / MAXIMA / 2002 / Remote Start
[PRINT THIS PAGE]
12volts      blue       +       ignition harness
Starter      BLACK/ red       +       ignition harness
Second Starter      BLACK/ white       +       ignition harness
Ignition      BLACK / YELLOW       +       ignition harness
Second Ignition                 
Third Ignition                 
Accessory      red       +       ignition harness
Second Accessory      WHITE/ blue       +       ignition harness
Keysense                 
Power Lock      ORANGE / black       -       driver door module
Notes: Meter these wires while turning the key in the driver door. Unlock requires a double pulse.
Power Unlock      ORANGE / blue       -       driver door module
Notes: Meter these wires while turning the key in the driver door. Unlock requires a double pulse.
Lock Motor      gray             pin 54 at SECU
Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column.
Unlock Motor      WHITE/ black             pin 55 at SECU
Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column.
Parking Lights+      RED / blue             driver kick panel
Notes: Can also find RED / green or RED / yellow at fuse box.
Parking Lights-      lt. blue             headlight switch
Hazards                 
Turn Signal(L)                 
Turn Signal(R)                 
Reverse Light                 
Door Trigger                  SECU
Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column.
Find lt. green for the drivers door in pin 1, RED / blue for the passenger front door in pin 2, and RED / white for the rear doors in pin 3. Use all 3 wires and diode isolate each.
Dome Supervision      use door trigger            
Trunk/Hatch Pin      purple / YELLOW       -       pin 13 at SECU
Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column.
Hood Pin      yellow/red       -       pin 6 at SECU
Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column.
Trunk/Hatch Release      blue             pin 16 at SECU
Notes: Requires a high-current ground for activation.
The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column.
Power Sliding Door                 
Factory Alarm Arm      arms with lock            
Factory Alarm Disarm      disarms with unlock            
Disarm No Unlock                 
Tachometer      WHITE/ green             instrument cluster
Notes: Located on the rear of the instrument cluster in the white plug. Do not start the car with the cluster unplugged. Can also find the WHITE/ green at the ECM located in the front of the center console on the transmission hump. The wiring is easily reached by removing the panel just to the front of the center console on the passenger side. DO NOT UNPLUG THE ECM.
Wait to start                 
Brake Wire      RED / green       +       brake switch or drivers kick
Parking Brake                 
Horn Trigger      GREEN / WHITE       -       steering column
Memory Seat 1                 
Memory Seat 2                 
Memory Seat 3                 
Immobilizer Bypass Module:      Required: Yes      Type: Transponder      Part #: 556U or 555U
Notes: N/A
warning      
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.
Jediknight1274 
Member - Posts: 4
Member spacespace
Joined: November 14, 2004
Location: United States
Posted: November 15, 2004 at 8:20 AM / IP Logged  

Definitly a start. thanks a lot.

SMCinMD

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Monday, May 13, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer