the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2003 Dodge Caravan remote start


Post ReplyPost New Topic
< Prev Topic Next Topic >
DrBriones 
Member - Posts: 9
Member spacespace
Joined: November 14, 2004
Location: Canada
Posted: November 21, 2004 at 4:21 PM / IP Logged  

Thanks guys.  You have been very helpfull.  I already have the bypass module (haven't installed it yet).

Now, in the installation manual they talk about the "glow plug light"... what is that?  And also for the interior light illumination output they talk about a relay which I haven't found.  do i have to buy one?  where do i install it if so?

thanks  So far I think I am doing well.

Roberto Briones
Ottawa, On
Canada
gus1 
Gold - Posts: 1,013
Gold spacespace
Joined: October 15, 2003
Location: Canada
Posted: November 22, 2004 at 3:34 PM / IP Logged  
Glowplug light is only necessary on a diesel.... and, unfortunately, we won't be getting any of the diesel powered Caravans in North America any time in the near future. Too bad really.... they go like hell, and get 42ish MPG while they're at it.
Gus
Wherever I go, that is where I end up......
DrBriones 
Member - Posts: 9
Member spacespace
Joined: November 14, 2004
Location: Canada
Posted: November 22, 2004 at 3:42 PM / IP Logged  
Thanks Gus!  That was starting to be a real pain in the  *ss
Roberto Briones
Ottawa, On
Canada
DrBriones 
Member - Posts: 9
Member spacespace
Joined: November 14, 2004
Location: Canada
Posted: November 22, 2004 at 5:11 PM / IP Logged  
Does anybody know where to find it (heater A/C color) in a 2003 Caravan?
Roberto Briones
Ottawa, On
Canada
swamprat323 
Gold - Posts: 1,335
Gold spacespace
Joined: September 22, 2002
Location: Florida, United States
Posted: November 22, 2004 at 5:16 PM / IP Logged  
ACCESSORY|*11              
*11 Accessory is not required for remote start.
that all my info says
Image6902 
Member - Posts: 45
Member spacespace
Joined: November 05, 2004
Location: United States
Posted: November 24, 2004 at 2:29 PM / IP Logged  
this is a very complex install for a beginner, may want to rethink having professionally installed. recommend using relays for anything having resistors (lock/unlock/2nd start wire) also recommend soldering all resistors. test lock/unlock resistors with vehicle at rest and while running, if resistance isn't close enough, while running the locks may not work. spent alot of time myself under the dash of these multiplexed nightmares, so have fun....
I tell it like it is...
DrBriones 
Member - Posts: 9
Member spacespace
Joined: November 14, 2004
Location: Canada
Posted: November 24, 2004 at 5:51 PM / IP Logged  

Hi again, I can't seem to find the wire that monitors the vehicle's RPM.  The Instruction manual says it is the one that in idle it measures 1-5 volts in AC (volts) and increases by 1-5 when RPMs increase to 3,000-4,000 RPMs.  I haven't found it.  The diagram that I have for my car (2003 caravan) says it is very accessible in the PCM PIN 11 of the 40-pin connector and the color matches, but it just doesn't measure what the install manual says.  Another diagram that I have says it is a completely different cable color that also exists in that harness, but not very accessible, and doesn't measure wnat tha manual says.

If someone could please tell me which one is I would appreciate it.

Roberto Briones
Ottawa, On
Canada
daniel2002p 
Silver - Posts: 524
Silver spacespace
Joined: October 10, 2003
Location: United States
Posted: November 24, 2004 at 6:06 PM / IP Logged  
the easiest way is to go to one of the fuel injectors, and use the odd colored wire.
2005 Toyota Corolla S
    1.8L VVT-i I-4
Always double check your wires with a DMM!!!
Do Not Use A Test Light!!!
MECP Certified Installer!
Best Buy 665 - IN IT TO WIN IT! TEAM MOBLE!
Ravendarat 
Platinum - Posts: 2,806
Platinum spacespace
Joined: February 23, 2004
Location: Canada
Posted: November 25, 2004 at 11:37 PM / IP Logged  
I second that, just strip back the tape on two injectors and they will each have two wires, on each injector one wire will be the same color, use the other color at either injector.
double-secret reverse-osmosis speaker-cone-induced high-level interference distortion, Its a killer
Page of 2

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Saturday, May 4, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer