the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

astroflex 1100 remote start install


Post ReplyPost New Topic
< Prev Topic Next Topic >
merlinlee 
Member - Posts: 3
Member spacespace
Joined: December 10, 2004
Location: Canada
Posted: December 10, 2004 at 12:10 AM / IP Logged  
 Hi all.

Installing a astroflex remote start into a 2004 trailblazer. I've got the AstroChart program which is great for most installs except for a slight discrepency in this perticular truck. The Green park lamp trigger wire from the R.S Module goes to the park lamp feed circuit. The picture of the wire to spice into is located at base of steering coloum a taped wire loom runs across the top of the drivers knee. In that wire loom is a Brown 12ga wire that is suppose to be the Parklamp feed. it only seems to supply power to the dash lights and. I suppose I'll have to remove the fuse/relay box under rear seat and locate the wire at the relay. At least I've got the bypass modules that run the doorlocks through the serial bus circuit.

I hate remote starters. Lots of requests for installs and if we dont do them its a 2 hr drive south for install. It was only -35C day before yesterday so I guess thats why all requests.

thanks

9 years exp auto tech
ck auto 
Copper - Posts: 257
Copper spacespace
Joined: September 20, 2003
Location: Canada
Posted: December 10, 2004 at 1:18 PM / IP Logged  
hi parklights are gray black at switch they are a negative trigger this truck uses data module for locks and security
good luck
kirk
merlinlee 
Member - Posts: 3
Member spacespace
Joined: December 10, 2004
Location: Canada
Posted: December 10, 2004 at 1:52 PM / IP Logged  
So a bosch relay powered by the parklight output from the astrostart with a ground output from pin 30 to the grey/blk wire should do the trick.
thanks
9 years exp auto tech
seracis 
Member - Posts: 17
Member spacespace
Joined: November 24, 2004
Location: United States
Posted: December 11, 2004 at 5:28 PM / IP Logged  
use one of the progammable outputs and set to park lights.  BUT, the park light wire IS brown but not 12ga. in the harness running horizontally under the column.  The correct one works all park lights, not just dash.
furredoutgixxer 
Member - Posts: 35
Member spacespace
Joined: December 11, 2004
Location: United States
Posted: December 11, 2004 at 10:35 PM / IP Logged  

they are both right the color is grey/black and is negative at the column or brown in the drivers kick positive. use either but i recommend grey/black.

MECP Master Installer


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Tuesday, February 7, 2023 • Copyright © 1999-2023 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer