blower not working with remote start

Home / the12volt's Install Bay / Car Security and Convenience / blower not working with remote start (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

pmes17

Member - Posts: 5

Joined: January 07, 2005

Posted: January 18, 2005 at 8:40 PM / IP Logged

i have a compustar 2WASS and everything works great except when i trigger the remote start, the blower never kicks on until i put the key in the ign and put it to start. What wire did i put in the wrong place. The car is a 95 thunderbird. TIA

Craig3708

Copper - Posts: 155

Joined: January 30, 2004

Location: Canada

Posted: January 18, 2005 at 8:44 PM / IP Logged

Ignition #1:	RED / LIGHT GREEN	IGNITION SWITCH HARNESS
Ignition #2:	GRAY / YELLOW (# AWG)	IGNITION SWITCH HARNESS **
Ignition #3:	GRAY / YELLOW-2WIRES	IGNITION SWITCH HARNESS **
Accessory:	BLACK/ LIGHT GREEN

If all these wires are powered up , everything should work fine.

Craig

BoominRolla

Copper - Posts: 198

Joined: September 06, 2004

Location: United States

Posted: January 18, 2005 at 9:29 PM / IP Logged

Your definately not powering up an ACCESSORY! check again the wire you got is a BLACK/ light green that tests as positive with the key on then shuts off while cranking then goes positive again once the vehicles running

mo12v

Platinum - Nominee - Posts: 2,748

This member consistently provides reliable information

Joined: September 30, 2003

Location: Afghanistan

Posted: January 18, 2005 at 10:00 PM / IP Logged

Ignition Switch Layout:

Starter..................RED / L BLUE.
Ignition #1..............RED / L GREEN (Primary Ignition).
Ignition #2..............GRAY / YELLOW (2) (Blower Motor) *
Ignition #3..............GRAY / YELLOW (Heat/Ac Controls).
Accessory................BLACK/ L GREEN (Radio/Wipers).
* 2 Of The 3 GRAY / YELLOW Wires Listed Are The Same Circuit.

Don't Learn from Others Mistakes

You Might Be the One That Knows.

pmes17

Member - Posts: 5

Joined: January 07, 2005

Posted: January 19, 2005 at 12:55 AM / IP Logged

all i konw is i have the Starter, Ign 1, and ign 2 hooked up ill have to look at the accessory and 3 ign tommarrow. Right now I Have the + Accesory to the gray / YELLOW. Which wire is the 2 ign and the 3 ign for the CM3000. The only thing im reading about is the 2 ign 200mA output. Please shed some light the car runs and starts fine right now except the blower kicking on and i have no way of telling if the radio works b/c theres no radio in the car right now.

forbidden

Platinum - Posts: 5,352

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

Joined: November 01, 2003

Location: Alberta, Canada

Posted: January 21, 2005 at 12:55 PM / IP Logged

Meter all of the lines coming from the ignition cyclinder under normal key start. Figure out which ones are giving you power when the key is in and turned to on. Write down the color and status of each wire. Remote start the vehicle and do the same, compare the two. Once the unit is remote started, take a temporary jumper from the red or red / white +12 volt constant and jump it to the wire that did not match in the written comparison, chances are that this is your wire that is the acc. that needs to be powered up.

Top Secret, I can tell you but then my wife will kill me.

leobito

Member - Posts: 3

Joined: February 03, 2003

Location: United States

Posted: January 21, 2005 at 2:30 PM / IP Logged

Re-Check your accesory wire !!

kgerry

Platinum - Posts: 3,455

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: January 21, 2005 at 5:03 PM / IP Logged

i've done this before ... there are mulitple grey / YELLOW wires and you are not powering up the correct one... usually it's the thickest of the three that needs to be hooked up.....

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

blower not working with remote start

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.