compustar help

Home / the12volt's Install Bay / Car Security and Convenience / compustar help (

Topic Closed)

Welcome Guest :)

Members

< Prev Page < Prev Topic Next Topic >

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 31, 2005 at 10:46 PM / IP Logged

techie51 wrote:

Just tried it again with the other remote still no output. I have the 12v constant to a 16 gauge fused wire I got run directly to the posts on the fuse box. The multimeter reading has it for 12v. Question for you does the door have to be open or closed when programming. I have tried both but not too keen on the wire I have for the door pin. It is the correct one but I have 3 wires going to the pink wire in the DKP(1.violet wire..domelight, 2. RED / white -door sensing, and violet/blk for -trunk sensing) Do I need to diode isolate the wires. Also do I need to put a relay on the domelight and the door locks. So many questions I appreciate your help.

When programming the remote for the Compustar, it doesn't matter wether or not if the doors, trunk or hood is open or shut. Regardless, all you need for the programming for the remote controls is the main harness & the antenna plugged in. As far as the door trigger's, you'll need to diode isolate the wires or you will get false alarms. The domelight you need to put a relay on it because the dome light wire is only a low current trigger wire. The door locks I would use relays for both lock and unlock to ensure a proper ground for unlock and use a resistor for the lock wire ( 1k ohm ).

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

techie51

Member - Posts: 24

Joined: January 11, 2005

Location: United States

Posted: February 01, 2005 at 2:34 PM / IP Logged

Just curious on how the brain could sense the IGN when there is no ign input on the module. I know that the DEI products did. I know what you are going to say, I should have gone with a DEI. Just pondering that questions.

techie51

Member - Posts: 24

Joined: January 11, 2005

Location: United States

Posted: February 01, 2005 at 2:40 PM / IP Logged

Never mind found the wiring guide for the CM3000 in the forum Answered my question. Forgive me just got to learn how to read... haha

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: February 01, 2005 at 4:40 PM / IP Logged

Post your results when you find out .

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

techie51

Member - Posts: 24

Joined: January 11, 2005

Location: United States

Posted: February 07, 2005 at 2:27 PM / IP Logged

I figured out what I was doing wrong. The battery has to be out of the 2way for programming. Also the whole process cannot take longer than 10 seconds. I was not turning the ignition over fast enough and did not have the battery out. The alarm works great and thanks for all your help. Next step is installing the door priority unlock. Once again thanks for all your help and suggestions.

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: February 07, 2005 at 2:44 PM / IP Logged

No problemo..... it seems that many installer's have the same problem wit the programming. The toggle of the IGN had to be done fast and furious in order for the learning of remote control to take.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

EGsiks

Member - Posts: 4

Joined: February 19, 2005

Location: United States

Posted: February 19, 2005 at 1:57 AM / IP Logged

what do you mean the battery has to be out of the 2 way?

techie51

Member - Posts: 24

Joined: January 11, 2005

Location: United States

Posted: February 19, 2005 at 4:37 PM / IP Logged

Yes according to the 2wss remote you must remove the AA battery while you are cycling 5 times. The biggest mistake I also made was that you have to program both remotes at the same time and within 10 sec. I alos must thank everyone especially Velocity Motors for being patient and helping me with this. You guys are great and definetly deserving of a donation.

here is the link to the 2WSS remote Thanks to several other posts:

http://www.nustart.ca/tech/Manuals/Firstech/2WSSR_user_manual.pdf

< Prev Page

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

compustar help

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.