the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Compustar CM3000 Brain Problem

Home / the12volt's Install Bay / Car Security and Convenience / Compustar CM3000 Brain Problem (Topic Closed Topic Closed)
Welcome Guest :)

Post ReplyPost New Topic
< Prev Topic Next Topic >
Velocity Motors 
Moderator - Posts: 12,488
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Fabrication. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: March 08, 2002
Location: Manitoba, Canada
Posted: February 14, 2005 at 7:11 PM / IP Logged  

Try relearning the remote controls. This takes it out of valet and also resets the controls.

Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
awsomedude 
Copper - Posts: 50
Copper spacespace
Joined: October 28, 2004
Location: United States
Posted: February 15, 2005 at 11:35 AM / IP Logged  
ok i made sure nothing was touching and tried to re learn the remotes, still nothing. I am running out of ideas.
iskidoo 
Silver - Posts: 1,040
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 08, 2002
Location: Maine, United States
Posted: February 15, 2005 at 12:06 PM / IP Logged  
Did you put the known good brain back into the other car to see if it works in there? Could you have a grounded hood pin wire or poor brain ground? Can you perform remote start take-over if the engine is started with the key?
awsomedude 
Copper - Posts: 50
Copper spacespace
Joined: October 28, 2004
Location: United States
Posted: February 15, 2005 at 1:22 PM / IP Logged  
I out the good brain back into the working car and it does not work in the working csr. I checked all the wiring and unplugged the harnesses that are not needed for the remote start to function. I am not able to put it in remote start mode when he car is running because the remote will not learn or respond.
Dutton 
Member - Posts: 15
Member spacespace
Joined: December 25, 2004
Location: United States
Posted: February 17, 2005 at 12:58 AM / IP Logged  

I have had this same problem  and have been looking for the solution  for  the past month and a half!  When you program the remote make sure only to go between the accesory and the on/starter, then it will get out of valet mode.  Now everything work perfectly.  Compustar is a great product with very sh*tty directions be ause they have  very poor translations into  English.  Good luck!

gus1 
Gold - Posts: 1,013
Gold spacespace
Joined: October 15, 2003
Location: Canada
Posted: February 17, 2005 at 4:18 PM / IP Logged  
Firstech isn;'t based in Texas any more??? I thought they spoke English quite well the last time I talked to them.
Gus
Wherever I go, that is where I end up......
Velocity Motors 
Moderator - Posts: 12,488
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Fabrication. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: March 08, 2002
Location: Manitoba, Canada
Posted: February 17, 2005 at 5:18 PM / IP Logged  

I just want to make sure that you are in fact toggling the ignition ( start in the OFF position ) to the ON position and finishing in the OFF position 5 times FAST ( within 3 seconds ) and finishing in the OFF position. I've told this to many member's of this forum and they all tell me " yeah I tried this and it didn't work " and then about 2 days later they tell me " .... oh , I guess I didn't toggle the ignition fast enough , it works great now, thanks "

I'm not saying that your wrong, but please just make sure that your toggling the ignition fast enough, flawlessly & ensuring that you have the remote control handy to press the lock button on the one way and button #1 on the 2 way remote .

Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
awsomedude 
Copper - Posts: 50
Copper spacespace
Joined: October 28, 2004
Location: United States
Posted: February 17, 2005 at 7:39 PM / IP Logged  
yeah I have installed plenty of these to know how to do it properly, the problem is whether or not the remote learns the tach button the brain should always respond when i push it, no matter what.
Page of 2

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, May 3, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved • Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer