First Time Installation

Home / the12volt's Install Bay / Car Security and Convenience / First Time Installation (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

Taito

Member - Posts: 8

Joined: February 16, 2005

Location: United States

Posted: February 21, 2005 at 10:15 PM / IP Logged

I just got a Compustar 2W900FM-AS and I am going to install it myself, and probably with a friend on a 97 Honda Accord with a factory security system. I have the wire diagram, so the question is for wiring I would match the car diagram with the brain diagram and mount the brain and some other things and that is it?? Anybody have any tips or instructions for a newbie?

Thanks

boomer_106

Silver - Posts: 710

Joined: November 25, 2003

Location: United States

Posted: February 21, 2005 at 10:41 PM / IP Logged

Take your time. Doublecheck your connections. Test the wires with your meter before you interface them. Soldering the wires is recommended. Have fun and learn alot.

johnnyb1231

Member - Posts: 34

Joined: February 20, 2005

Location: United States

Posted: February 22, 2005 at 1:02 AM / IP Logged

every piece of info you need for wiring your car First Time Installation - Last Post -- posted image.

12volts	white	+	ignition harness
Starter	BLACK/ white	+	ignition harness
Second Starter
Ignition	BLACK / YELLOW	+	ignition harness
Second Ignition
Third Ignition
Accessory	yellow	+	ignition harness
Second Accessory
Keysense
Power Lock	BLACK/ white	-	gray conn. above fuse
Notes: SE models, use factory alarm arm wire for lock and factory alarm disarm wire for unlock.
Power Unlock	orange	-	box in blue tape
Notes: SE models, use factory alarm arm wire for lock and factory alarm disarm wire for unlock.
Lock Motor	WHITE/ red		drivers door harness
Unlock Motor	yellow		drivers door harness
Parking Lights+	RED / black		blue plug fuse box
Notes: Also a male blade terminal is available in the fusebox DKP.
Parking Lights-
Hazards
Turn Signal(L)
Turn Signal(R)
Reverse Light
Door Trigger	blk/wht	-	gray plug right of column
Dome Supervision	use door trigger
Trunk/Hatch Pin	orange	-	gray plug right of column
Hood Pin
Trunk/Hatch Release
Power Sliding Door
Factory Alarm Arm	RED / yellow	-	passenger kick or alarm
Notes: Factory alarm is located under the passenger front seat.
Factory Alarm Disarm	RED / blue	-	passenger kick or alarm
Notes: Factory alarm is located under the passenger front seat.
Disarm No Unlock
Tachometer	blue	AC	at distributor
Wait to start
Brake Wire	GREEN / WHITE	+	brake switch
Parking Brake
Horn Trigger	blu/red or grn/blu	-	steering column
Memory Seat 1
Memory Seat 2
Memory Seat 3

Immobilizer Bypass Module:	Required: No	Type: N/A	Part #: N/A
Notes: N/A

alik

Member - Posts: 10

Joined: February 01, 2005

Posted: February 22, 2005 at 11:17 AM / IP Logged

WHERE DID YOU GET YOUR Compustar. i'M CURRENTLY LOOKING FOR A GOOD DEAL ON IT ?

Taito

Member - Posts: 8

Joined: February 16, 2005

Location: United States

Posted: February 22, 2005 at 3:38 PM / IP Logged

alik I got mine on ebay. You just have to keep a look out on ebay.

Ok so with the chart aboce I go to my alarm brain wireing diagram and match up each of the wires? So the chart says '12volt' is white and the alarm diagram '12volt' is red so I just crip the two wires together? Is that it or am I missing something else. Thanks for the help as you can tell this is my first time installing an alarm, I have done cd recievers, but thats different.

profuse007

Gold - Posts: 2,015

Joined: October 20, 2002

Location: Texas, United States

Posted: February 22, 2005 at 6:41 PM / IP Logged

AT or MT accord?

Houston,TX

"The two most common elements in the universe are H+ and stupidity" (Ellison).

Taito

Member - Posts: 8

Joined: February 16, 2005

Location: United States

Posted: February 22, 2005 at 8:47 PM / IP Logged

AT accord EX four door with factory security system, which I am probally going to take out.

johnnyb1231

Member - Posts: 34

Joined: February 20, 2005

Location: United States

Posted: February 22, 2005 at 9:11 PM / IP Logged

you might have a problem with the domelight coming on if you take out the factory alarm... we had an experience where after us unplugging the FA the domelight wouldnt come on with the doors open... so its just a matter of finding those 2 wires and connecting them

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

First Time Installation

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.