2002 Toyota Sequoia Remote Start

plain stand alone rem starter going in, cust keeping factory keyless entry.

I already explained  about toyota door locks dont work wile engine is running, he has no prob with it. I know it has a transponder.

last one I did I sortof remember the parking lights being a pain- it was last season-didnt take notes. I have a wire chart for it, just looking to see if anyone else has one I can compare mine to- or any heads ups?

thanks in advance men.

Here are three different sources that I have for the 2002 Sequoia:

|       ITEM      |     WIRE COLOR     |POL|       WIRE LOCATION        |

|              12V|wht/blue & wht/red  |+  |ignition harness            |

|          STARTER|BLACK/ white         |+  |ignition harness            |

|         IGNITION|BLACK/ red           |+  |ignition harness            |

|  SECOND IGNITION|BLACK / YELLOW        |+  |ignition harness            |

|        ACCESSORY|pink                |+  |ignition harness            |

|       POWER LOCK|see direct fax      |   |                            |

|     POWER UNLOCK|document #1070      |   |                            |

|       LOCK MOTOR|blue/red            |   |blk plug, pin 1 @ BECU *4   |

|     UNLOCK MOTOR|RED / black           |   |blk plug, pin 14 @ BECU *4  |

|    DISARM DEFEAT|blue/black          |   |blk plug, pin 2 @ BECU *4   |

| PARKING LIGHTS +|green               |   |back of fusebox, 12 pin plug|

| PARKING LIGHTS -|green               |   |headlight switch            |

|       HEADLIGHTS|yellow/red          |-  |headlight switch            |

|     DOOR TRIGGER|*1                  |-  |*1                          |

| DOME SUPERVISION|comes on with unlock|   |                            |

|  TRUNK/HATCH PIN|red                 |-  |in back door at ECU         |

|         HOOD PIN|blue/white          |-  |DKP, 26 pin plug in pin 4   |

|  FCTRY ALARM ARM|arms with lock      |   |                            |

|FCTRY ALRM DISARM|disarms with unlock |   |                            |

| DISARM NO UNLOCK|YELLOW /GREEN *3     |-  |ignition harness            |

|       TACHOMETER|YELLOW /GREEN        |   |ECM, 28 pin plug in pin 4 *2|

|      SPEED SENSE|GREEN/ orange        |   |ECM, 28 pin plug in pin 5 *2|

|       BRAKE WIRE|GREEN/ YELLOW        |+  |brake pedal switch          |

|     HORN TRIGGER|BLACK / YELLOW        |-  |steering column             |

|           WIPERS|blu/blk(L),blu/red(H|+  |steering column             |

|  LF WINDOW UP/DN|red - green         |A  |LF window switch            |

|  RF WINDOW UP/DN|red - green         |A  |RF window switch            |

|  LR WINDOW UP/DN|red - green         |A  |LR window switch            |

|  RR WINDOW UP/DN|red - green *5      |A  |RR window switch            |

| SUN RF OPN/CLOSE|not recommended     |   |                            |

|        RADIO 12V|blue / YELLOW         |+  |radio                       |

|     RADIO GROUND|brown               |-  |radio                       |

|     RADIO SWITCH|gray                |+  |radio                       |

| RADIO ILLUMINATE|green               |+  |radio                       |

|    POWER ANTENNA|WHITE/ blue          |+  |radio                       |

|       LF SPEAKER|pink - purple       |   |radio                       |

|       RF SPEAKER|lt. green - blue    |   |radio                       |

|       LR SPEAKER|black - yellow      |   |radio                       |

|       RR SPEAKER|red - white         |   |radio                       |

Notes:

NOTE:  This vehicle has an immobilizer system that needs to be bypassed when adding remote start.   *1 The two driver side door trigger wires are in a 14 pin plug in the driver kick panel. The driver door trigger is gray/red in pin 14, the left rear door is RED / white in pin 13. The two passenger side door trigger wires are in a 14 pin plug in the passenger kick panel. The front passenger door is lt. GREEN/ black in pin 14, and the right rear door is RED / white in pin 5. Use all four and diode isolate each.  *2 The ECM is behind the glove box.  *3 This is the ignition key sense wire. There are 2 YELLOW /GREEN wires in the ignition harness. The correct one is in a 2 pin plug. Using the status output wire from the remote start to ground this wire will disarm the alarm without unlocking the doors.  *4 The BECU (Body ECU) is above the driver kick panel.  *5 To interface with the tailgate window, must runs wires into the tailgate. The up motor wires is pink and the down motor wire is white.

Toyota

Sequoia

2001-2002

Remote Starter  Wiring Colors and Notes
Function		DTI Color	Vehicle  Color	Location
Start:		Yellow	BLACK/ WHITE	IGNITION SWITCH HARNESS *
Ignition  #1:		Blue	BLACK/ RED	IGNITION SWITCH HARNESS
Ignition #2:		Green	BLACK / YELLOW	IGNITION SWITCH HARNESS
Ignition  #3:		Wht/Blk	N/A
Accessory:		White	PINK	IGNITION SWITCH HARNESS
Brake  Light:		Orange	GREEN / WHITE	AT SWITCH ABOVE BRAKE PEDAL
Tach  Signal:		Green	YELLOW /GREEN	AT ECM PIN B4 **
Parking Lights:		Yellow	GREEN (+)	AT JUNCTION BLOCK ON PASSENGER SIDE AT ECM
Headlights:		Yellow
OEM Alarm  Disarm:		Brn/Wht	RED / YELLOW (-)	INSIDE OF DRIVER'S DOOR
OEM Alarm  Arm:		n/a
Diesel  Glow Plug:		RED / Black
Clutch  Bypass Wire:		n/a
Notes:		* This vehicle is equipped with a transponder immobilizer system. ** ECM is located behind the glove box on passenger side of the vehicle.

---

Toyota

Sequoia

2001-2002

Alarm and Keyless  Entry Wiring Colors and Notes
Function		DTI Color	Vehicle  Color	Location
Constant  +12 Volts:		Red	WHITE/ BLUE	IGNITION SWITCH HARNESS
Starter  Kill:		Vlt or Wht	BLACK/ WHITE	IGNITION SWITCH HARNESS *
Ignition  +12 Volts:		Orange	BLACK/ RED	IGNITION SWITCH HARNESS
Dome  Lights/Superv:		Brown	WHITE	AT BCM PIN B8***
OEM Horn:		Blue	WHITE/ RED (-)	DRIVER'S KICK PANEL
Power  Lock:		Wht/Red	SEE NOTE ****
Power  Unlock:		Yel/Red	SEE NOTE ****
Trunk  Release:		Grn/Wht
Alarm  Input Wire:		R/W or Gy/Bk	WHITE	AT BCM PIN B8***
Notes:		*** The BCM is located high on the drive's side underneath the dash. Test for correct wire. ****  Modern Toyota Door Locks.

WIRE	COLOR	LOCATION
12 VOLTS CONSTANT	WHT/BLU	IGNITION SWITCH HARNESS
IGNITION 1	BLK/RED	IGNITION SWITCH HARNESS
IGNITION 2	BLK/YEL	IGNITION SWITCH HARNESS
ACCESSORY /HEATER BLOWER 1	PNK	IGNITION SWITCH HARNESS
STARTER	BLK/WHT	DOTS STANDARD IGN HARNESS
PARKING LIGHTS	GRN (+)	AT JUNCT BLOCK ON PASS SIDE AT ECM
DOMELIGHT	WHT	AT BCM AT DRIVER'S SIDE UNDER DASH
PWR DOOR LOCK
PWR DOOR UNLOCK
TACH SENSOR	YEL/GRN	AT ECM
BRAKE	GRN/WHT (+)	AT BRAKE SWITCH
HORN	WHT/RED	DRIVER'S KICK PANEL
FACTORY DISARM	RED / YEL	IN DRIVER'S DOOR
FACTORY ANTI-THEFT	TYPE	TRANSPONDER

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

The pink accessory wire is not needed for remote start; the climate controls are powered by the BLACK / YELLOW second ignition wire.

Positive parking lights, as well as brake lights, are easily available in a plug in the driver's kick panel.

Hoodpin:  There are two 26-pin plugs that are VERY far forward and high up in the driver's kick.  The hoodpin is in the lower (gray) of these two plugs.  It shows a partial ground even with the hood closed----cut it in half, and attach two diodes to the "hood" side of the wire.  One diode goes to the other side of the blue/white you just cut; the second diode goes into your remote start.  (Only models with a factory alarm have a hoodswitch.)

Tach:  Forget about pulling down the glove box and going to the ECM.  Above the gas pedal is a cluster of maybe ten plugs--some gray, some black, and some white.  There are several YELLOW /GREENs in there; a few of those wires are tach.  You can also get it at the instrument cluster---either by removing the cluster, or reaching way, way up above the gas pedal, to the back of the cluster, and attaching a T-tap (with your bare fingers---no tools will fit).  Also, I'm not finding the tach above the gas pedal on the 2003s.

Factory alarm disarm:  Just like the DEI sheet says---ground the key sense wire during remote start.

Transponder bypass:  Toyotas are a little fussy about how you place the coil around the key cylinder.  You'll want to tape it to the very front edge, against the flat area where it lights up.  When you install the dash back on, it'll hold the coil there even better.

How to test if the car has a factory alarm:  Close the tailgate and hood.  Then do one of these three things:  1.  Open a door, press Lock on the door, and close it.  2.  Press Lock on the factory remote.  3.  Close all the doors, and then lock them using the key.  ------ The security light in the instrument cluster should come on steady for thirty seconds, and then begin to flash slowly--the system is now armed.  If the security light NEVER comes on steady, but just flashes slowly all the time, you do not have an alarm---the light only serves to warn about the transponder key.