the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

remote start on h. odessy


Post ReplyPost New Topic
< Prev Topic Next Topic >
camino 
Copper - Posts: 54
Copper spacespace
Joined: October 15, 2002
Location: Mexico
Posted: December 01, 2002 at 9:27 PM / IP Logged  

hi. i'm have to install a remote star  on this2002 odessy.and the customer want's to be able to use the sliding door's,the van came with a factory remote to do that,so i decided to install a 700t hornet and a valet remote start module,no problem,the problem was when i remotly start the vehicle the keyless entry don't work,i know is because  the baypass module is sending the pulse for the key sense,and when the key is on the ignition ,the keyless entry dont work,i know where is the keyless module.i cut the wire  from the key sense,(blue/withe)and still the same,for now the van has the viper remote start,but the customer wants the sliding door working with a remote control,any help will be great, thanks guy's. 

el camino
securinu 
Silver - Posts: 772
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: September 15, 2002
Location: United States
Posted: December 01, 2002 at 10:39 PM / IP Logged  
you need to find the ignition feed to the factory module and cut it thru a relay during remote start.
jrilla 
Gold - Posts: 1,498
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: November 19, 2002
Location: North Dakota, United States
Posted: December 02, 2002 at 8:54 AM / IP Logged  
Securino, do you know what wire is the ignition feed into the factory module?  Camino, I am just curious what kind of range that factory remote gets.  Have you tested it or has the customer tested it?  I have a customer who wants a starter put in their Odyssey and they were willing to use two remotes, but if the factory remote works at a decent range, then I could just install an add-on.
J Rilla
Owner/Installer
securinu 
Silver - Posts: 772
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: September 15, 2002
Location: United States
Posted: December 02, 2002 at 4:45 PM / IP Logged  
i am not sure but there cant be that many wires to test , also i have a diagram on how to get those sliders to work with an aftermarket remote if you need it.
jrilla 
Gold - Posts: 1,498
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: November 19, 2002
Location: North Dakota, United States
Posted: December 02, 2002 at 5:30 PM / IP Logged  

I would like to see that wire diagram, but you would need a few extra channels for that right? 

You can send an email to: js12vinstallations@hotmail.com  or you can post it if you want.

J Rilla
Owner/Installer
camino 
Copper - Posts: 54
Copper spacespace
Joined: October 15, 2002
Location: Mexico
Posted: December 02, 2002 at 11:07 PM / IP Logged  
i know what wire you talking about,is yellow,but it didn't work,the think is when you put the key ,even without turning it to the ignition position,the keyless dont work,any way i'll install the sliding door with the viper remote start,3rd and 4rd chanel'sthanks,and about the diagram  i did my own design and work's good.jrilla i recomend you to install an aftermaket,it's better for the range.ok?and if yo u have any question let me know.
el camino
jrilla 
Gold - Posts: 1,498
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: November 19, 2002
Location: North Dakota, United States
Posted: December 03, 2002 at 5:17 AM / IP Logged  
let me know what you you guys have hooked up to.  I assume you just pulse a wire for each door using a relay, that is how I have done other sliding doors.  email or post your information.  Thanks a lot.
J Rilla
Owner/Installer
camino 
Copper - Posts: 54
Copper spacespace
Joined: October 15, 2002
Location: Mexico
Posted: December 03, 2002 at 11:06 PM / IP Logged  
well this cain of door,is not that easy,is data bus,to open and close,is not simply a pulse,so you have to build a set of relay's and a module to be able to do it..
el camino
10nesne1 
Silver - Posts: 284
Silver spacespace
Joined: June 19, 2002
Location: British Columbia, Canada
Posted: December 04, 2002 at 10:27 AM / IP Logged  

Hey Camino

I email the diagram to Jrilla.  If you post your email address then I can email you the diagram.  It's very easy to hook it up.  I did a couple this summer. 

10nesne1

Velocity Motors 
Moderator - Posts: 12,488
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Fabrication. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: March 08, 2002
Location: Manitoba, Canada
Posted: December 04, 2002 at 1:06 PM / IP Logged  
Hey

10nesne1, please email this to me and I will post it on the TECH TIPS page for other's to access aswell. My email is velocity@valleycable.com

Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer