2004 Chrysler Concorde wiring chart

Hi guys, I've got a 2004 Chrylser Concorde coming in Saturday for a remote start install, does anyone have access to a wiring chart?  Thanks!!Soylent Green is People

DIRECTWIRE™ WIRING INFORMATION - CHRYSLER / CONCORDE / 2004 / Remote Start 12volts red (40A), pink/black (40A)   +   ignition harness Starter yellow   +   ignition harness Second Starter N/A        Ignition dk. blue/white   +   ignition harness Second Ignition dk. GREEN/ red   +   ignition harness Third Ignition N/A        Accessory BLACK/ orange   +   ignition harness Second Accessory BLACK/ white   +   ignition harness Keysense lt. blue   -   ign harn or BCM, black plug, pin 24 Notes: The BCM is attached to the back of the junction block, at the driver side end of the dash. The plugs for the BCM face the firewall. Power Lock WHITE/ dk. green   +   BCM, blue plug, pin 5 Notes: Lock is positive trigger thru a 2.7K ohm resistor. Unlock is positive trigger thru a 620 ohm resistor. MUST use relays. The BCM is attached to the back of the junction block, at the driver side end of the dash. The plugs for the BCM face the firewall. Can also use Directed 457C or 456L interface modules. Power Unlock same as power lock wire        Lock Motor orange   5wi back of junc block, brn plug, pin 3 Unlock Motor dk. blue   5wi back of junc block, brn plug, pin 7 Parking Lights+ BLACK / YELLOW   +   back of junc block, gry plug, pin 11 Parking Lights- yellow   -   switch or BCM, black plug, pin 2 Notes: Parking lights are negative trigger thru a 47 ohm resistor. MUST use a relay. The BCM is attached to the back of the junction block, at the driver side end of the dash. The plugs for the BCM face the firewall. Hazards same as turn signal wires        Turn Signal(L) lt. green   +   back of junc block, brn plug, pin 11 Turn Signal(R) tan   +   back of junc block, brn plug, pin 10 Reverse Light PURPLE / black   +   back of junc block, brn plug, pin 12 Door Trigger see notes   -   BCM, blue plug Notes: The LF door is tan in pin 4, RF door is tan/red in pin 2, LR door is tan/red in pin 1, and RR door is tan/red in pin 10. Use all four wires and diode isolate each. The BCM is attached to the back of the junction block, at the driver side end of the dash. The plugs for the BCM face the firewall. Dome Supervision yellow   -   front of junc block, tan plug, pin 4 Trunk/Hatch Pin tan/black   -   driver kick, harness to rear Hood Pin N/A        Trunk/Hatch Release BLACK/ white   +   switch or BCM, gray plug, pin 1 Notes: The BCM is attached to the back of the junction block, at the driver side end of the dash. The plugs for the BCM face the firewall. Power Sliding Door N/A        Factory Alarm Arm lt. GREEN/ orange   +   BCM, blue plug, pin 13 Notes: Arm is positive trigger thru a 1.87K ohm resistor. Disarm is positive trigger thru a 680 ohm resistor. MUST use relays. The BCM is attached to the back of the junction block, at the driver side end of the dash. The plugs for the BCM face the firewall. Can also use Directed 457C or 456L interface modules. Factory Alarm Disarm same as factory alarm arm wire        Disarm No Unlock see factory alarm disarm        Tachometer NOT dk. GREEN/ lt. green   ac   any ignition coil or fuel injector Wait to start N/A        Brake Wire WHITE/ tan   +   brake pedal switch Parking Brake gray/black   -   back of junc block, tan plug, pin 1 Horn Trigger BLACK/ red   -   back of junc block, gry plug, pin 6 Memory Seat 1 pink/red   -   switch or memory mod under dr seat Memory Seat 2 pink/white   -   switch or memory mod under dr seat Memory Seat 3 N/A   -      Interface Module: Category: Immobilizer Bypass Required: Yes Type: Sentry Key Part #: 555CW Alternate Part1 #: 556UW Alternate Part2 #: 555U Alternate Part3 #: DesignTech 20402 Alternate Part4 #: DesignTech 29402 Notes: Only vehicles with gray keys have the immobilizer. Interface Module: Category: Door Lock Interface Required: Yes Type: Data Bus Part #: 457CW Alternate Part1 #: 456LW Notes:        This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. Be careful whose advice you buy, but be patient with those who supply it.