the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

cutting pexiglass correctly?


Post ReplyPost New Topic
< Prev Topic Next Topic >
atsronnyats 
Member - Posts: 2
Member spacespace
Joined: October 29, 2005
Location: United States
Posted: November 09, 2005 at 4:16 PM / IP Logged  
ok i need to know how to cut say 1/4 in and 1/8 in pexiglass and say 1/16 to 1/32 sheet metal properly because im sure the correct tool is about the only one to use without it break and not conforming correctly so help with that would be appreciated im going to use this to mod my computer but the knowlegde id like to have for an amp rack i plan to make in the future out of pexi using neon lighting etc... so your know ledge is muy apreciated! thanx
____________________________________________________________
97 Rolla CE pair of kx6.5 components and DX693ways on a 240 watt 4 channel and a rockford cd player
liquidx9 
Member - Posts: 5
Member spacespace
Joined: November 09, 2005
Location: United States
Posted: November 09, 2005 at 9:10 PM / IP Logged  
Cut plexi with a jigsaw and a router. Make a template out of MDF, cut with a plactic blade in your jigsaw, then flush trim the rough cut plexi to the template. Don't use the same bit you use to cut wood with to make as clean a cut as possible. If my rough cut line is more than the width of the router bit(I use a 1/2" shank) I'll go around the piece ,attached to the template with 2 sided tape, with a bearing thats 1/4" bigger than the shaft, then flush it with my finishing bit.
///Alpine/MB Quart/Image Dynamics/Soundstream/Stinger
smurphalurph 
Member - Posts: 31
Member spacespace
Joined: July 10, 2005
Location: United States
Posted: November 11, 2005 at 2:05 AM / IP Logged  
I just use the Dremel with a dimond plated cut-off wheel.
When you do things right, people won't realize you've done anything at all.
Ocuriel 
Copper - Posts: 141
Copper spacespace
Joined: December 01, 2004
Location: United States
Posted: November 26, 2005 at 5:38 PM / IP Logged  
What if you use a big ruler, clamp it down & deeply score a line along the ruler. Then just bend the plexi at the scored line so it can crack. I've never tried cutting plexi, but if i had to, I would try this befor eanything.
note: this is only to cut straight lines.   
menace2sobriety 
Silver - Posts: 394
Silver spacespace
Joined: October 29, 2005
Location: United States
Posted: November 26, 2005 at 11:43 PM / IP Logged  
i just tried scoring and it did not work to well. it splintered for plexi that the end are not showing i use a skill saw with a 40 tooth blade. and it works fine.
captain_zap 
Member - Posts: 10
Member spacespace
Joined: October 30, 2005
Location: United States
Posted: November 27, 2005 at 2:07 AM / IP Logged  
leave it to me to suggest a lazer for true detail work....
With respect to scoring, it works, on sheets, I have had it work on 1/8" and other small stuff but past that it. Its futile not to mention dangerous...I have enough nicks scrapes and razor knife accidents on the job, on my own and from midnight fabrication marathons without trying to saw through acrylic with one. for holes, a hole saw works ok run in reverse, literally melting thought the acrylic. Plastic drill bits are also a useful investment if you plan to do allot of acrylic fabrication. For a PC modder the best tools are likely the dremell, the die grinder for the better equipped, the nibbler, a basic power drill, and a nibbler, the nibbler is an invaluable tool to get small holes and used to be a common PC modder tool to do big windows on a low budget, just wear gloves or get big blisters, you can get very smooth results with hardly any filling.
realitycheck 
Silver - Posts: 751
Silver spacespace
Joined: September 09, 2004
Posted: November 28, 2005 at 2:03 PM / IP Logged  

I just bought a nibbler to do sheet metal work for shaving door handles. It is amazing. I just cant get mine to cut intricate shapes because of the back side of it. So I just use sheet metal snips to do that. About $20 bucks at your local air and heating supply store.

Learning the trade one fiberglass creation at a time!
auex 
Platinum - Posts: 5,041
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 23, 2002
Location: Arizona, United States
Posted: November 28, 2005 at 2:16 PM / IP Logged  
Best way for installers is the router. Make a template out of wood, double sided tape it to the plexi, and then run the router to the outside of it. You can do it with a jig saw but make sure that you have a fine toothed blade in it and take your time.
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: November 28, 2005 at 3:39 PM / IP Logged  
When your done....try taking a scrap piece, and get out your propane torch. Flame polish the edges....looks good. test it....not too hot the stuff melts and burns.cutting pexiglass correctly? -- posted image.
DukeDuke 
Silver - Posts: 206
Silver spacespace
Joined: November 01, 2003
Location: United States
Posted: December 06, 2005 at 11:32 PM / IP Logged  
My best recommendation is the router, and if you have the balls and are good enough a jig saw with a high tooth count blade, like everyone else mentioned. As well as for clean up, get some 220 grit give it all a nice sand, then take it to your buffer and get some good polish and polish it up, then if you have to, go up to 400 and polish again. Comes out CRYSTAL clear. Good luck. If you want to be a lazy PC modder(like myself) by yourself a prefab plexi case. They are only like $30.00 now. Good luck!
Duke Duke

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer