the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Viper xv791 remote start problem


Post ReplyPost New Topic
< Prev Topic Next Topic >
jones100001 
Member - Posts: 42
Member spacespace
Joined: November 15, 2004
Posted: February 06, 2006 at 5:35 PM / IP Logged  

Fastlearner wrote:
did you hook up the tach  wire. Sounds like you didn't or you didn't hook it up to the right wire. Did you tap the in put for the relay to the mini four pin harness off the relay pack.

I hooked up the tach wire correctly.

Only time my car will remote start is if I have the key at ON position. 

Wether remote start toggle switch is on or off, remote start will try to start the car but doesn't actually start.  Car keeps cranking but doesn't catch.

mobilecustoms 
Silver - Posts: 397
Silver spacespace
Joined: November 04, 2005
Posted: February 06, 2006 at 7:40 PM / IP Logged  
do you have the second starter wire hooked up correctly?
also on the ignition 1 did you use the smaller gauge BLACK/ red wire?
the starter 1 will either be
BLACK/ RED or BLACK/ WHITE
also the 2 accessory wires?
jones100001 
Member - Posts: 42
Member spacespace
Joined: November 15, 2004
Posted: February 06, 2006 at 9:09 PM / IP Logged  

mobilecustoms wrote:
do you have the second starter wire hooked up correctly?
also on the ignition 1 did you use the smaller gauge BLACK/ red wire?
the starter 1 will either be
BLACK/ RED or BLACK/ WHITE
also the 2 accessory wires?

There's only 1 accessory wire which is Orange from alarm.  There are 2 accessory wires?

I cut thicker (BLACK/ red - starter #1) wire in half.  I connected green wire from alarm to harness side.  I connected the purple wire from alarm to the other side.

I cut (BLACK/ blue - starter #2) wire in half.  I made a jumper wire which connects from purple wire from alarm to this BLACK/ blue wire.  I didn't connect it to the harness side but the other side of the cut. 

I connected pink wire from alarm to thinner (BLACK/ red - ignition).  I connected pink/white from alarm to (red - ignition #2 ??? )  Not sure if the red wire on ignition harness is ignition #2

I connected orange wire from alarm to (WHITE/ blue - 2nd accessory)

I connected the red wires from alarm to (green - 12v)

jones100001 
Member - Posts: 42
Member spacespace
Joined: November 15, 2004
Posted: February 07, 2006 at 9:08 AM / IP Logged  
After playing around a bit, I got to a point where car starts only if I have the key inserted.  If I don't have key inserted, my remote start won't work.
h2oskierfl 
Copper - Posts: 87
Copper spacespace
Joined: April 20, 2005
Location: United States
Posted: February 07, 2006 at 11:29 AM / IP Logged  
There is something wrong with your 555U. Check your wiring and placement of your cylinder ring.
mobilecustoms 
Silver - Posts: 397
Silver spacespace
Joined: November 04, 2005
Posted: February 07, 2006 at 12:26 PM / IP Logged  
ok
the second starter needs a relay- use the trigger wire from the 4 small wires off the acrs pack- purple
second accessory use another relay and use the orange off the xcrs do not connect it straight to the wire
the second starter should not be cut
the 4 wires from the xcrs that are small gauge are relay trun on wires and should not be directly connected tot he wire in the car without the use of a relay
also check the bypass that it is mounted correctly around the cylinder.
jones100001 
Member - Posts: 42
Member spacespace
Joined: November 15, 2004
Posted: February 07, 2006 at 2:03 PM / IP Logged  

h2oskierfl wrote:
There is something wrong with your 555U. Check your wiring and placement of your cylinder ring.

Are you suppose to keep your valet key in the 555U?

mobilecustoms 
Silver - Posts: 397
Silver spacespace
Joined: November 04, 2005
Posted: February 07, 2006 at 2:21 PM / IP Logged  
yes or else the car will not remote start
it will remote start if you have the key in the ignition cylander
jones100001 
Member - Posts: 42
Member spacespace
Joined: November 15, 2004
Posted: February 07, 2006 at 8:42 PM / IP Logged  
If remote starter works w/ either ON and OFF remote start toggle switch, is there problem w/ the swtich itself or wiring problem?
wranglercory 
Copper - Posts: 53
Copper spacespace
Joined: January 27, 2005
Location: United States
Posted: February 08, 2006 at 11:04 AM / IP Logged  
See if you can go into programing if you can than the valet button is working , after that I would try to program the unit for voltage sense . This way you can see if the ring is in the right place .
Page of 3

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer