spacer spacer spacer spacer

Tips to FG the whole trunk?

Post ReplyPost New Topic
< Prev Topic Next Topic >
Copper - Posts: 116
Copper spacespace
Joined: April 01, 2005
Posted: April 03, 2006 at 7:58 PM / IP Logged  
so ive done one project... FG one sub in each corner of my car (rx8)... i've recently been craving to do another project... now i wanna go big.. i wanna do my whole trunk... my only concern is the size of everything... the boxes ive made (pictured) just BARELY fit.. in order to get them in my trunk you have to angle it a certain way.. and its a tight fit.. and i dont wanna build this whole FG box and not be able to fit it in my trunk.. i know im going to have to create several pieces... also how do i make them flow like its one giant piece?
Tips to FG the whole trunk? - Last Post -- posted image.
Tips to FG the whole trunk? - Last Post -- posted image.
Tips to FG the whole trunk? - Last Post -- posted image.
Member - Posts: 21
Member spacespace
Joined: March 31, 2006
Posted: April 03, 2006 at 10:32 PM / IP Logged  

My advice to you would be simply build it in ur trunk. thats about all u can do if ur gonna make it one big piece

Silver - Posts: 433
Silver spacespace
Joined: September 19, 2004
Location: United States
Posted: April 04, 2006 at 8:36 AM / IP Logged  
Try building a model out of cardboard that will resemble your final idea and test fit w/ that. That's what I do when making my boxes to ensure that they fit into trunks properly. Also check to see if that back seat comes out. That can often be a larger and easier to pull in/out of the trunk. And if that doesn't work then I'm gonna have to go w/ jesse on the idea of one large box built in the trunk. Piecing a fg enclosure together in a trunk while keeping it properly sealed and looking good will be dificult, very difficult
Copper - Posts: 85
Copper spacespace
Joined: July 18, 2004
Location: United States
Posted: April 05, 2006 at 11:04 AM / IP Logged  
im just finishing up a trunk setup in a corvette, and i found it easiest to make it mostly out of MDF. you'll definately end up with at least one seam in your design (i had 3 considering there are 3 amp racks), but another things that helps is iff you use a cover for your trunk buildup. what i did was built a false floor with some glass trim that went up to the trunk trim( it's a corvette, so the hatch made for a decent amount of open space between the weather stripping and the straight edged MDF). It looks alright right now (hasnt been sueded yet so we'll see how it looks finished later), but if you can get in there and make a good single piece Fiberglass trunk covering (in other words if you can make a single piece and still be able to pull it out of the car when it's done) then i'd say to do that.
2000 Chevrolet S10
Premier DEH-P860MP
JL Audio XR650-CSi components
Boston 4x6 splits
JL Audio 10W3v2
Alpine MRP-M350
Clarion APA-4162
Copper - Posts: 232
Copper spacespace
Joined: November 15, 2005
Location: United States
Posted: April 07, 2006 at 9:37 PM / IP Logged  
do the back seats fold down?  What type piece are you looking to make?  And don't forget, you can always take the weatherstripping off for a few more mm.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Follow Follow on Facebook
Friday, January 27, 2023 • Copyright © 1999-2023, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo spacer spacer spacer
Top spacer spacer