Wiring Diagram

Home / the12volt's Install Bay / Car Security and Convenience / Wiring Diagram (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

stevepara

Member - Posts: 4

Joined: January 21, 2003

Location: United States

Posted: January 22, 2003 at 7:47 AM / IP Logged

I am in need of a wiring digram for a pontiac transport montana extended, with keyless entry. need to install auto alarm with auto start.

thank you in advance

steve

stevesnap@hotmail.com

10nesne1

Silver - Posts: 284

Joined: June 19, 2002

Location: British Columbia, Canada

Posted: January 22, 2003 at 9:03 AM / IP Logged

Pontiac

Montana

1998-2002

Remote Starter Wiring Colors and Notes
Function		Vehicle Color	Location
Start:		YELLOW	IGNITION SWITCH HARNESS *
Ignition #1:		PINK	IGNITION SWITCH HARNESS
Ignition #2:		WHITE	IGNITION SWITCH HARNESS (PCM)
Ignition #3:		N/A	****
Accessory:		ORANGE	IGNITION SWITCH HARNESS (HEAT/AC) **
Brake Light:		WHITE (+)	AT SWITCH ABOVE BRAKE PEDAL
Tach Signal:		WHITE	AT POWERTRAIN CONTROL MODULE
Parking Lights:		BROWN (+)	AT HEADLIGHT SWITCH
Headlights:		YELLOW (+)	AT HEADLIGHT SWITCH
OEM Alarm Disarm:		GREEN/ BLACK (-)	16 PIN CONNECTOR IN DR. KICK PANEL
OEM Alarm Arm:		N/A	SEE NOTES BELOW **
Diesel Glow Plug:
Clutch Bypass Wire:
Notes:	*Equippes with transponder anti-theft system - Use Universal Alarm Bypass Module following for "Transponders." See Installation Note #233 GM High Current Ignition if equipped with rear heat. ****All DesignTech remote starters except the 2xx22 have an ignition 3 output - it is the WHITE/ black in the 'control harness.' This wire will be used to control the anti-theft bypass module.

Pontiac

Montana

1998-2002

Alarm and Keyless Entry Wiring Colors and Notes
Function		Vehicle Color	Location
Constant +12 Volts:		RED & RED	IGNITION SWITCH HARNESS
Starter Kill:		YELLOW	IGNITION SWITCH HARNESS *
Ignition +12 Volts:		PINK	IGNITION SWITCH HARNESS
Dome Lights/Superv:		GRAY/BLACK (-)	AT BODY CONTROL MODULE ***
OEM Horn:		BLACK (-)	STEERING COLUMN HARNESS
Power Lock:		RED / BLACK (-)	AT BODY CONTROL MODULE ****
Power Unlock:		WHITE	AT BODY CONTROL MODULE ****
Trunk Release:		N/A
Alarm Input Wire:		GRAY/BLACK (-)	AT BODY CONTROL MODULE ***
Notes:	* BCM Is Located To The Right Of The Glove Box. ** Negative Door Lock System.

stevepara

Member - Posts: 4

Joined: January 21, 2003

Location: United States

Posted: February 05, 2003 at 7:49 AM / IP Logged

Thank you for a rapid response, are there any resistors that need to be used, and would you know where the wire for the electric sliding door is, would like to use it on chsnnel 3 of alarm.

Player69

Silver - Posts: 504

Joined: October 27, 2002

Posted: February 05, 2003 at 8:46 AM / IP Logged

Sliding door is lt.blue in the overhead console - pulse.

No resistors are required.

This van has passkey3.

Hvra

Member - Posts: 1

Joined: February 05, 2003

Location: Mexico

Posted: February 05, 2003 at 9:25 PM / IP Logged

i need the conections for honda civic 89 for install an alarm. i wonder if you help me .. tanks

Player69

Silver - Posts: 504

Joined: October 27, 2002

Posted: February 05, 2003 at 9:37 PM / IP Logged

Hvra start a new topic and someone will likey reply.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Wiring Diagram

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.