1998 plymouth grand voyager remote start

Home / the12volt's Install Bay / Car Security and Convenience / 1998 plymouth grand voyager remote start (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

orton1000

Member - Posts: 1

Joined: December 19, 2002

Location: United States

Posted: January 26, 2003 at 4:19 PM / IP Logged

Need help with two things on this vehicle

first all the codes that i pull up list the tach wire for a 2.4l engine but this one has a 3.0 chrysler engine and i can't find the tach wire to hook up to

and secondly it doesn't have a keyless entry with this vehicle but it does have power locks and i can't find the lock and unlock wires either

any help with my situation would be appreciated

remember keep it simple

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 26, 2003 at 6:16 PM / IP Logged

| TACHOMETER|gray or gray/red | |ignition coil

*2 --------- Use relays and set up for negative trigger. Place a 4020 ohm resistor inline on the lock output, and a 665 ohm resistor inline on the unlock output. If you do not have a factory security system use a 1500 ohm for lock and a 250 ohm for unlock.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

dfiddy

Copper - Posts: 162

Joined: August 17, 2002

Location: Canada

Posted: January 26, 2003 at 10:10 PM / IP Logged

the tach should be gray/red and the ignition coil should be located in the middle behind the engine close to the firewall...pretty sure anyways...

zargon

Copper - Posts: 186

Joined: January 27, 2003

Location: United States

Posted: January 27, 2003 at 7:22 PM / IP Logged

the lock and unlock wire is at the bottom of the fuse box it is white with dark green not white with lte green. it is tight to get to but you can do it without pulling loose the fuse box, just cut that tough tape and usually the lock wire is first one up, good luck tach is in an easy spot at top of engine to the back.

zargon ruler of estranorth

Haku

Copper - Posts: 204

Joined: November 22, 2002

Location: United States

Posted: January 27, 2003 at 8:25 PM / IP Logged

Also.. Tach wire can be found at the Powertrain contol module. Gray/Red.

Powertrain control module is found on the drivers fenderwell.

Hak

Siemens Autostart

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

1998 plymouth grand voyager remote start

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.