security lamp, 1998 gmc seirra

Home / the12volt's Install Bay / Car Security and Convenience / security lamp, 1998 gmc seirra (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

wscovil

Member - Posts: 15

Joined: January 01, 2006

Location: United States

Posted: January 01, 2007 at 12:10 PM / IP Logged

im having problems with my 1998 gmc seirra P\u starting and stalling and the security lamp flashes. i tried installing a RCS and now i can not start the truck .i even tried unpugging the car starter and still not helping..any advice would greatly be appriciated!!

thanks

Wayne

chris354

Silver - Posts: 253

Joined: February 19, 2005

Location: United States

Posted: January 01, 2007 at 12:18 PM / IP Logged

Did you use a theft bypass module. You need one to bypass the passlock 2 theft system.

wscovil

Member - Posts: 15

Joined: January 01, 2006

Location: United States

Posted: January 01, 2007 at 12:36 PM / IP Logged

I Installed the starter first and then when i went to hook up the bypass module (XK06) i noticed that the wiring colors ect did not match what i had.so i thought that i could still start the truck normally until i could figure out the bypass details.the truck already had a Artic start starter and a bypass (no name on it).but it has always gave me problems when it get real hot inside the truck so i thought i would change it.i just unhooked the bypass and resoldered the wires back togather.

Wayne

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 01, 2007 at 5:38 PM / IP Logged

Make sure that there is not another break on the wire for the Passlock wire ( use a DMM and set to continuity ).

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

wscovil

Member - Posts: 15

Joined: January 01, 2006

Location: United States

Posted: January 01, 2007 at 5:42 PM / IP Logged

jeff,do you happen to know which wire it is?also do you know if i tried to start the truck with the wire not hooked up ..would it put into some kind of security mode?

thanks for your help .

Wayne

chris354

Silver - Posts: 253

Joined: February 19, 2005

Location: United States

Posted: January 01, 2007 at 6:29 PM / IP Logged

There should be a yellow and a black wire that runs up to the ignition switch they are thin wires usually the yellow wire is cut into for most bypasses. If the truck get the wrong code I think you have to turn the key on for like 12 minutes then it should start as long as the wires are intact.

wscovil

Member - Posts: 15

Joined: January 01, 2006

Location: United States

Posted: January 01, 2007 at 6:34 PM / IP Logged

ok thanks,i'll try that .

Wayne

au5599

Copper - Posts: 94

Joined: December 22, 2005

Location: United States

Posted: January 01, 2007 at 7:57 PM / IP Logged

xk06 can be an issue. What is it stamped for on the top? They can be preprogrammed for several different interfaces.

Also passlock II wires are thin wires usually yellow, orange with black stripe and red with white stripe. On some they did yellow, black and white.

Make sure all wires are fully intact again. Then turn on and try starting with key. If it trips security leave key on for 15 minutes and come back turn off then back on and it should start up and run. Then you need to figure out if you got the right interface program for the xk06 to work on that truck.

Street Dreams Car Club

93 GRAND CARAVAN SE / Astro

Team New York SS3-4 06 & SM3-4 07 DB Drag World Finals

2003 Chevy Suburban LT / 98 GTP

wscovil

Member - Posts: 15

Joined: January 01, 2006

Location: United States

Posted: January 01, 2007 at 8:17 PM / IP Logged

My XK06 is PKG7. I havnt had it fully hooked up because i couldnt decipher where the wires went ..the colors that they to use ,i didnt have on mine.so i resoldered the yellow wire back togather and just unpluged the remote starter. also i tried leaving the key on for 15 mins.then i turned it off and tried to start but the sercuity light just keeps flashing and the truck just stalls .this thing is driving me crazy .:)

Wayne

au5599

Copper - Posts: 94

Joined: December 22, 2005

Location: United States

Posted: January 02, 2007 at 8:29 AM / IP Logged

wscovil wrote:

The XK06 is wrong. It will NOT work on that truck. You need it programmed for a PLXR

How are the other 2 wires? either orange with black stripe and red with white stripe or black and white wires?

after 15 minutes was the security light flashing?

Make sure you try to start with key first, then leave the ignition on without shutting it off. Wait the 15 minutes.

Street Dreams Car Club

93 GRAND CARAVAN SE / Astro

Team New York SS3-4 06 & SM3-4 07 DB Drag World Finals

2003 Chevy Suburban LT / 98 GTP

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.