fiberglass enclosure sub ring

Home / the12volt's Install Bay / Fiberglass, Fabrication, and Interiors / fiberglass enclosure sub ring (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

racerx22

Copper - Posts: 57

This member has made a donation to the12volt.com. Click here for more info.

Joined: May 24, 2005

Location: United States

Posted: February 01, 2007 at 11:22 AM / IP Logged

This is what it used to be. Same height but couple inches wider

fiberglass enclosure sub ring - Page 2 -- posted image.

specialaudio

Copper - Posts: 58

Joined: April 15, 2006

Location: Canada

Posted: February 01, 2007 at 8:49 PM / IP Logged

what are we looking at ?

93' Cutlass

racerx22

Copper - Posts: 57

Joined: May 24, 2005

Location: United States

Posted: February 04, 2007 at 6:25 PM / IP Logged

trying to figure how to make the sub ring for my new enclosure for these subs. The mounting diameter is 13 3/4" inches. I got one sheet if 1/2" mdf and 1 sheet of 3/4" mdf..Both sheets are 2ft x 4ft

firelizard

Copper - Posts: 54

Joined: January 02, 2006

Location: Canada

Posted: February 08, 2007 at 11:25 AM / IP Logged

1 half inch should do it for the flushing ring...I am guessing those subs are hefty so maybe the 3 quarters for the base ring?

Just cut rings to spec with a jigsaw and sand them to make them nice and round, then nail and glue them together

racerx22

Copper - Posts: 57

Joined: May 24, 2005

Location: United States

Posted: February 17, 2007 at 4:02 PM / IP Logged

HEre are the pics of the rings. Not the best. but its first time for everything.

[IMG]https://i124.photobucket.com/albums/p9/LiLJit07/MVC-051S-1.jpg[/IMG]

[IMG]https://i124.photobucket.com/albums/p9/LiLJit07/MVC-053S.jpg[/IMG]

[IMG]https://i124.photobucket.com/albums/p9/LiLJit07/MVC-057S.jpg[/IMG]

[IMG]https://i124.photobucket.com/albums/p9/LiLJit07/MVC-058S.jpg[/IMG]

[IMG]https://i124.photobucket.com/albums/p9/LiLJit07/MVC-059S.jpg[/IMG]

[IMG]https://i124.photobucket.com/albums/p9/LiLJit07/MVC-060S.jpg[/IMG]

[IMG]https://i124.photobucket.com/albums/p9/LiLJit07/MVC-061S.jpg[/IMG]

rkaczar

Member - Posts: 16

Joined: November 03, 2006

Location: United States

Posted: February 18, 2007 at 8:27 PM / IP Logged

looks better on the second attempt with some support but you might find it hard to stretch still because of how low the subs are angled in the middle, but its worth a shot. just take your time and use patience.

disturbing the peace since 1984

racerx22

Copper - Posts: 57

Joined: May 24, 2005

Location: United States

Posted: February 19, 2007 at 9:47 AM / IP Logged

What about the rings i just made? HEre are the pics of the rings. Not the best. but its first time for everything.

fiberglass enclosure sub ring - Page 2 -- posted image.

racerx22

Copper - Posts: 57

Joined: May 24, 2005

Location: United States

Posted: February 20, 2007 at 11:20 AM / IP Logged

Whut u think?

racerx22

Copper - Posts: 57

Joined: May 24, 2005

Location: United States

Posted: February 25, 2007 at 8:48 PM / IP Logged

Aight finally finished all the stapling. next time im going to get an air stapler b.c my hand is killing me right now. There is sag in the middle of the rings because thats where I pulled some of the material to make it tighter. Not the best stapling job.

rkaczar

Member - Posts: 16

Joined: November 03, 2006

Location: United States

Posted: February 26, 2007 at 7:26 PM / IP Logged

looks good.make sure you saturate that thing good with resin until its shiny. and when you get ready to put fiberglass on it precut it into like 3x3" squares. it gets a little messy when you cut as you go.

disturbing the peace since 1984

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.