the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

hooking up heated seats w/ starter?


Post ReplyPost New Topic
< Prev Topic Next Topic >
attackdog 
Member - Posts: 17
Member spacespace
Joined: November 07, 2002
Location: United States
Posted: May 04, 2007 at 4:34 PM / IP Logged  
Hi all:
I have a 2001 GMC Yukon and need to know how to hook up the heated seats to my auto-starter? Is there an easy way to do it like in the kick panel or do I need to go to the switch in the driver's door? Thanks.
-Dean
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: May 05, 2007 at 12:33 AM / IP Logged  
You must go to the switch in the door. Look on the back of the little board. Look at it with the actual switch to the right. Just below the switch you will see 2 large solder points. Down to the left, and down to the right. Wire a relay like this 86 12volts, 85 use the trunk output from the unit. 30 thru a 2K resistor goes to the solder point on the left. 87 get's the other solder point. AFTER REMOTE STARTING....push the trunk pop, the drivers seat will turnm on high, hit the trunk pop again, it will switch to low, again, it will turn off. This works.....have fun!
secured_auto 
Member - Posts: 8
Member spacespace
Joined: October 16, 2006
Location: United States
Posted: May 05, 2007 at 2:21 AM / IP Logged  
I think easier way way to use GMDLBP which does it too....
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: May 05, 2007 at 9:08 AM / IP Logged  
Information I have says this part does not work on this year, for heated seats.?
attackdog 
Member - Posts: 17
Member spacespace
Joined: November 07, 2002
Location: United States
Posted: May 05, 2007 at 2:45 PM / IP Logged  
Um... What??? Sorry for not getting the lingo.
-Dean
attackdog 
Member - Posts: 17
Member spacespace
Joined: November 07, 2002
Location: United States
Posted: May 05, 2007 at 2:45 PM / IP Logged  
secured_auto wrote:
I think easier way way to use GMDLBP which does it too....
Um... What??? Sorry for not getting the lingo.
-Dean
Ravendarat 
Platinum - Posts: 2,806
Platinum spacespace
Joined: February 23, 2004
Location: Canada
Posted: May 05, 2007 at 2:47 PM / IP Logged  
They were talking about using a data interface module to control the seats through the computer, my info however also says that that wont work and you need to do the relay method to activate the seats.
double-secret reverse-osmosis speaker-cone-induced high-level interference distortion, Its a killer
attackdog 
Member - Posts: 17
Member spacespace
Joined: November 07, 2002
Location: United States
Posted: May 05, 2007 at 3:06 PM / IP Logged  
Ravendarat wrote:
They were talking about using a data interface module to control the seats through the computer, my info however also says that that wont work and you need to do the relay method to activate the seats.
Sounds good. I will give the relay method a shot. Are the resistors neccesary or can I just run the relay alone? Thanks again.
-Dean
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: May 05, 2007 at 8:43 PM / IP Logged  
The 2000 ohm resistor IS needed.
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: May 05, 2007 at 8:47 PM / IP Logged  

secured_auto wrote:
I think easier way way to use GMDLBP which does it too....

Does kind look like some super dooper instant message lingo crap...doesn't it....? Thats funnyhooking up heated seats w/ starter? -- posted image.

Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Sunday, September 19, 2021 • Copyright © 1999-2021 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer