radio, no power, fuses ok

Home / the12volt's Install Bay / Car Audio / radio, no power, fuses ok (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Page < Prev Topic Next Topic >

perly

Copper - Posts: 155

Joined: April 24, 2004

Location: Canada

Posted: October 13, 2007 at 8:29 PM / IP Logged

any bare metal is a good ground. just make sure that you scratch/sand away any paint before you ground it

Back to Top

techman93

Silver - Posts: 591

Joined: October 28, 2006

Location: Pennsylvania, United States

Posted: October 14, 2007 at 7:56 AM / IP Logged

If you would have read my post originally you would have not had to have asked that question.

techman93 wrote:

Constant 12V+ GREEN/ YELLOW

Switched 12V+ Yellow/Black

Illumination Blue/Red

Dimmer n/a

Antenna Trigger ORANGE / Blue

Antenna Right Front

Front Speakers 5" x 7" Doors

Left Front (+) ORANGE / Green

Left Front (-) BLACK/ White

Right Front (+) WHITE/ Green

Right Front (-) BLACK/ White

Rear Speakers 5" x 7" Side Panels

Left Rear (+) Pink/Green

Left Rear (-) Pink/Blue

Right Rear (+) Pink/Blue

Right Rear (-) GREEN/ Orange

I have advice if this isn't of help ... run new wires.

Find a solid ground and ring terminal end of wire and attach by a ground already in vehicle or clean off paint from metal in driver kick and screw in with self tapping screw.

Run a wire direct to battery with a 20 amp fuse close to battery for a constant 12v source. Or at ignition wires in steering column.

Constant 12V+ BLACK/ Orange Ignition Switch Harness

and add fuse here 15 - 20 amps in a fuse holder

Ignition RED / Green Ignition Switch Harness

you can fuse this one if you feel like it to be safe with same as for constant 12v+.

Hope you get your radio working.

Back to Top

lightbulbcomics

Member - Posts: 7

Joined: October 02, 2007

Location: Ohio, United States

Posted: October 14, 2007 at 8:08 AM / IP Logged

I did read your post, but didn't know what you meant by driver's kick.

Anyway, I got it working. Thanks to everyone.

Back to Top

Search for other posts by lightbulbcomics

extreme1

Silver - Posts: 1,070

Joined: February 12, 2003

Location: Canada

Posted: October 14, 2007 at 12:21 PM / IP Logged

lightbulbcomics wrote:

Hopefully someone can give a novice some advice. According to the below chart, this should be the configuration of my wiring:

https://www.the12volt.com/installbay/stereodetail/1469.html

Now, I tested the wires using a test light, and the results I got are my constant & switched 12v get nothing, there is a large red wire that seems to have the power in any key position. The illumination is OK, and antenna trigger blew out my test bulb!

So I tried wiring my yellow & red to the large red wire, and ground to ground= nothing.

Any help?

that big red wire in the radio harness is the ground.

Shaughn Murley

Install Manager, Dealer Services

Visions Electronics

Red Deer, Alberta

Back to Top

< Prev Page

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

radio, no power, fuses ok

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.