the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Help installing new amp


Post ReplyPost New Topic
< Prev Topic Next Topic >
Oly_e5 
Member - Posts: 6
Member spacespace
Joined: October 01, 2003
Location: United States
Posted: October 06, 2003 at 6:10 PM / IP Logged  
I am about to be installing an XMD1000P5 sony xplod amp 500W RMS at 4 Ohm and 900W RMS at 2 ohm and it has a fuse rating of 120amp(comes with 3 40amp fuses in the amp).  Crutchfield suggests that I use a 150amp fuse next to the battery.  I am wondering if this is important, does the amp at the battery have to be atleast 120amps??  Do I absolutley need a fuse at the amp??  I am confused??  Can anyone help me out??
auex 
Platinum - Posts: 5,041
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 23, 2002
Location: Arizona, United States
Posted: October 06, 2003 at 7:02 PM / IP Logged  
Yes, fuses are important, unless you like car-b-q. Do you need a 150 amp, probably not. But you do need something. I would reccommend a 100 amp circuit breaker or something close to that.
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
bberman1 
Gold - Posts: 2,314
Gold spacespace
Joined: March 11, 2002
Location: United States
Posted: October 06, 2003 at 7:09 PM / IP Logged  
With a 120 amp fuse rating that amp would be capable of putting out just over 1500 watts rms. Now its rms rating @ 2ohms is 1000 watts, so there is a good chance that the amp may be under rated. Now as far as fusing the amp, the only necessary fuse to add would be a 120 amp fuse within 18 inches of the battery. Now with a 120 amp rating you will need to use an ANL fuse http://www.darvex.com/miva/merchant.mv?Screen=PROD&Store_Code=D&Product_Code=GANL125PT&Category_Code=FANL and fuse holder http://www.darvex.com/miva/merchant.mv?Screen=CTGY&Store_Code=D&Category_Code=FH Now you have to select the inline ANL fuse holder accordingly with your cable size. For that amp you will need at least a 4 gauge cable so you will want a 4 gauge ANL fuse holder http://www.darvex.com/miva/merchant.mv?Screen=PROD&Store_Code=D&Product_Code=CQ-2200-0&Category_Code=FH
Oly_e5 
Member - Posts: 6
Member spacespace
Joined: October 01, 2003
Location: United States
Posted: October 07, 2003 at 1:57 AM / IP Logged  
Once again I am going to be installing a XPD1000P5 Sony Mono (L+R) amp and the amp has 3 40amp fuses in it.  I have seen that you can use an ANL fuse of a 120amps or more or I can use a circuit breaker, but with the circuit breaker I dont know how big to use??  Just wondering what the pro's prefer or suggest.
fuseblower 
Silver - Posts: 403
Silver spacespace
Joined: June 25, 2003
Location: United States
Posted: October 07, 2003 at 7:01 AM / IP Logged  

A circuit breaker is operates just as the fuse. You can also use a circuit breaker that is 120 amps or greater. The biggest advantage is that when you trip a circuit breaker you just flip the switch back to on when you find out what caused it to flip off. With a fuse you have to spend a few dollars for another fuse. The down side to a circuit breaker is that when you want to upgrade you have to get another breaker and with a fuse you just get a larger fuse. If you are going to have more than one amp you will need to get a circuit breaker that will accommodate both amps.

superstreet786 
Silver - Posts: 339
Silver spacespace
Joined: August 12, 2003
Location: United States
Posted: October 07, 2003 at 7:34 PM / IP Logged  
I also think you should only need a 120 amp fuse by the battery.  Just use the same for the battery as you use for the amplifier.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer