the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

turn on lead for 3 amps


Post ReplyPost New Topic
< Prev Topic Next Topic >
dreem363 
Member - Posts: 5
Member spacespace
Joined: April 14, 2006
Posted: May 17, 2006 at 3:06 AM / IP Logged  

Hey guys I need some help with my audio system.  I have (2) 2ch fosgate amps and (1) 4ch Alpine amp that I'm planning to install on my audio system. I also know that a turn on lead wire connected to the HU is needed in order to avoid the amp always being on. 

I also know that a relay is a good idea when more than (2) amps are used.  My question is....

How should the 3 amps be connected on the relay(87,86,30,etc.) and do i need a small fuse after the relay? which connection from the relay should go directly to the HU?

mustangfoo 
Silver - Posts: 371
Silver spacespace
Joined: November 16, 2005
Location: United States
Posted: May 17, 2006 at 3:40 AM / IP Logged  

ok you are gonna wanna connect the relay like so. . . . .

85 remote turn on lead FROM HU

86 Ground

30 FUSED constant, or you could even be better off with ACC power since its for your amps. MAKE SURE you fuse it though.

87 New output for remote turn on leads, connect this to your amps.

dreem363 
Member - Posts: 5
Member spacespace
Joined: April 14, 2006
Posted: May 17, 2006 at 8:39 PM / IP Logged  
87 is the output for the turn on leads from the amps.  Do I connect all three wires from amps to this single wire and then connect it to the 87 input? Crimping splicing?
forbidden 
Platinum - Posts: 5,353
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: November 01, 2003
Location: Alberta, Canada
Posted: May 17, 2006 at 8:50 PM / IP Logged  

You can jump the turn on wire from amp to amp. Run one wire from the relay to the first amp, then from that amp to the next, then the next. You will not be drawing any huge amount of current at all. As far as the suggestion to wire it to constant, not the best bet unless you want your amps to never turn off. Always wire to a source controlled by the ignition cylinder, be it ACC or IGN.

Top Secret, I can tell you but then my wife will kill me.
Clif 
Member - Posts: 46
Member spacespace
Joined: November 30, 2004
Location: United States
Posted: May 17, 2006 at 8:51 PM / IP Logged  
yea, just connect all three to 87 however you want to.
hmmm.... was that the right wire?

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer